Q 2. For a modulating signal m(t) = 2 cos 100t + 18 cos 2000t, (a) Write expressions for Phase modulated signal,øpM (t) and Frequency modulated signal, Pem(t) when A=10, wc = 106,k, = 1000n, k, = 1. For determining opm(t), use the indefinite integral of m(t), that is, take the value of the integral at t = -00 to be 0. (b) Estimate bandwidths of øPm(t) and wfm(t).

Q 2. For a modulating signal m(t) = 2 cos 100t + 18 cos 2000t, (a) Write expressions for Phase modulated signal,øpM (t) and Frequency modulated signal, Pem(t) when A=10, wc = 106,k, = 1000n, k, = 1. For determining opm(t), use the indefinite integral of m(t), that is, take the value of the integral at t = -00 to be 0. (b) Estimate bandwidths of øPm(t) and wfm(t).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The carrier c(t) = 100 cos(2πft) is frequency modulated (FM) by the message signal m(t) = 5 cos( 20000πt), where f.= 100MHz. The peak-frequency deviation is 20 kHz. The modulated signal is a wide-band FM.1. Determine the amplitude and frequency of all signal components that have a power level of at least 10% of the power of the unmodulated carrier component.2. From Carson's rule, determine the approximate bandwidth of the FM signal.
An interview is held with a student about the importance of education for thirty minutes at a radio station. It was later amplitude modulated & transmitted to receivers on the school campus.The expression below describes the transmitted signal a(z) a(z)= Acos(16πz) where A=3cos(10πz) a. In an expression form, express a(z) as a sum of sinusoids & determine the frequency components of the signal a(z)b. To adequately & fully recover the signal at the receiver, determine the rate at which the signal should be sampled.c. Determine the discrete signal,a[n] that was transmitted in a reduced form & the angular frequency assuming the signal a(z) is sampled at ten Hertz.
A frequency modulated signal is generated by modulating the carrier signal c(t) = 40 cos(2pi fc t),with fc = 106 MHz.The phase function of the FM modulated signal is known to be phase(t) = 10 sin(12,000pi t).Determine1. the average transmitted power of the FM modulated signal u(t),2. the peak-phase deviation,3. the peak-frequency deviation,4. the bandwidth of the FM modulated signal.
a. In an RC circuit supplied with AC power, a 500 ohm resistor is used to create a system with a crossover frequency wc =440 rad/s. What capacitance is the capacitor in this circuit? b. If an inductor is to be added to this circuit to make the resonant frequency equal to the crossover frequency, then what inductance must this inductor have? c. If, near a particular time t1, the instantaneous voltage drop over the resistor is given by v(t1)=0.65V cos(440t), then what is i(t1) (the function of instantaneous current with respect to time) for its capacitor? d. What would the Irms value be based on the sinusoidal function you found in part c? (Pick off Ipeak from the function, then plug in to rms equation) Since this is multi-part, answers to later parts will be graded based on your answers to previous parts when necessary.
a) In an RC circuit supplied with AC power, a 500 ohm resistor is used to create a system with a crossover frequency wc =440 rad/s. What capacitance is the capacitor in this circuit? b. If an inductor is to be added to this circuit to make the resonant frequency equal to the crossover frequency, then what inductance must this inductor have? c. If, near a particular time t1, the instantaneous voltage drop over the resistor is given by v(t1)=0.65V cos(440t), then what is i(t1) (the function of instantaneous current with respect to time) for its capacitor? d. What would the Irms value be based on the sinusoidal function you found in part c? (Pick off Ipeak from the function, then plug in to rms equation)
Given m(t) = sin 2000 πt, kf = 200,000π, and kp = 8000 π.Find frequency deviation, Δf, for(i) Frequency Modulated (FM) signal(ii) Phase Modulated (PM) signal.
Consider a FM signal given by equation VFM (t) = 5 Cos [2x108 πt + 3 sin (40000πt)]. Calculate carrier frequency, modulating frequency, frequency deviation and bandwidth
The carrier signal of amplitude 10V is frequency modulated (K=2kHz/V) by a signal with frequency spectrum shown: a. Determine the approximate bandwidth of the FM signal (Bessel approximation).b. Determine the approximate bandwidth of the FM signal (Carson approximation).c. The power dissipated by the FM signal in a 75-ohm antenna.Answers a) 24 kHzb) 16 kHzc) 0.667 W
Which of the following is incorrect? a)Both the frequency and phase of the FM modulated carrier signal change depending on the information signal. b)The spectrum of the angle modulated signal is similar to the spectrum of the m(t) signal, as is the spectrum of the analog modulated signal. c)The instantaneous frequency of the angle expression q(t)=2000πt+π/2.u(t-3) is fi(t)=1000+π/4.δ(t-3). d)The angle modulated signal is obtained by linearly changing the phase or frequency of the carrier with the information signal.
In case the sound from the engine of a vehicle is modelled by the function y(t) = cos[ω(t + τ) + θ] where time delay=τ & phase=θ Determine the frequency & period of the signal u(t) whena)[ω, τ, θ] = [π/3, 1/2, π/2]b)[ω, τ, θ] = [3π/4, 1/2, π/4] N.b time should be in seconds & frequency in Hertz. c) y(t) = e-atu(t) for t≥0 & y(t) = 0 for t<0 where a>0 is a constant The function above defines the model of the decay of the vibration of a vehicle engine. i.Make a sketch of the signal y(t) & determime its fourier transform.
In the circuit in the figure, Vcc= 18 V, Rs1 = 0.9 kohm, Rohm = 0.5 kQ, R1 = 75 kohm, R2 = 15 kohm, RC = 2.2 kohm, RE = 1 kohm and B = 120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = C = 44 pF and Cce = 11 PF. Accordingly, considering the frequency response of the circuit, what would the high cutoff frequency (fH) be? NOTE-1: The output impedance of the transistor is ro = 20 k and will be taken into account in the calculations. NOTE-2: high frequency dependence of hfe, B. will be taken into account.
A series R L C circuit is operating in a resonance mode. The input voltage signal is: u (t ) =150square root of 2 sin (1000 t - 45deg), V . Find the capacitance C, the characteristic impedance ρ, the quality factor Q, the effective (RMS) values of the voltage drops across the passive elements. Given are: R = 10 Ω, L=100 mH. Use the condition for voltage resonance.