Q# 2:1 Chapter 14: Gas vapor mixtures and air-Conditioning (Psychrometric chiart) CLO 4 dbity to design air conditioning systems using the psychrometric chart, and mass and energy balance relations Air enters an air-conditioning system at 20C and 70 percent relative humidity at a rate of 2 m' /min It is cooled to 15 °C and saturated when the liquid water leaves the system at 32°C. Calculate the amount of water removed from the air and the rate of heat removal from the air.

Q# 2:1 Chapter 14: Gas vapor mixtures and air-Conditioning (Psychrometric chiart) CLO 4 dbity to design air conditioning systems using the psychrometric chart, and mass and energy balance relations Air enters an air-conditioning system at 20C and 70 percent relative humidity at a rate of 2 m' /min It is cooled to 15 °C and saturated when the liquid water leaves the system at 32°C. Calculate the amount of water removed from the air and the rate of heat removal from the air.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 1RQ: The standard design conditions for air-conditioning systems established by the Air-Conditioning,...

See similar textbooks

Similar questions

The standard design conditions for air-conditioning systems established by the Air-Conditioning, Heating and Refrigeration Institute (AHRI) are outside temperature _____F, inside temperature ______F, with a humidityof____%.
Use the concept of evaporative cooling to explain how air’s relative humidity is measured using a sling psychrometer
f. A single-family detached residence of moderate construction has a total sensible load of 53,300 Btu/hr. The design humidity ratio is 0.021 lb of vapor/lb of dry air. Determine the total cooling load.
( Handwritten Sol) The air in a house is at 19°C, 59% relative humidity, and total pressure 89kPa. If air is cooled at constant pressure, the temperature at which moisture begins to codense is:
RH2 = 43% What is the specific humidity of the air stream #1, w1 (lbm H2O/lbm air)? What is the specific humidity of the air stream #2, w2 (lbm H2O/lbm air)? What is mass flow rate of dry air in stream #1 (lbm/s)? What is mass flow rate of dry air in stream #2 (lbm/s)? What is the relative humidity of the outlet (%)?
Moist air enters a duct at 10oC, 80% relative humidity, and a volumetric flow rate of 81m3/min. The air is heated as it flows through the duct and exists at 34oC. No moisture is added or removed. Draw the cycle on the attached chart and determine: a) The rate of heat transfer in KJ/s; b) The relative humidity at the exit.
Air (mass of dry air: 3 kg) with a relative humidity of 50% at 25 °C is supplied isobaric 30 kJ. What is the relative humidity after that?
6-Prove that the enthalpy of the humid air remains constant along a wet bulb temperature line on the psychrometric chart
Air at 24 °C dry-bulg and 15 °C wet-bulb enters a humidifier and leaves at 41 °C dry-bulb and 21 °C wet-bulb. How much moisture has been added per kilogram of dry air?
a stream of outdoor air is mixed with a stream of return airin an airconditioning system that operates at 101 kpa pressure.the flow rate of outdoor air is 3kg/s and its condition is 30 C Tbd and 23 C Twb. the flow rate of return air is 2.5 kg/s and its condition is 15 C Twb and 60% RH. Determine:a - enthalpy of mixture b - humidity ratio of mixturec- dry bulb temperature of mixtured- dry bulb temperature by the weighted average of the dry bulbtemperature of the entering streams
Moist air exists at a dew point temperature of 18°C, 60% RH, and a pressure of 96.5 kPa. Determine the humidity ratio and specific volume.
In each duct (A and C), air conditioning processes described below take place:In the AB duct, a cooling process is produced with a little humidification in which an atmospheric air flow of 28 m3/min enters at a temperature of 45°C and a relative humidity of 10%, as it is a process where moisture is injected into the air, its relative humidity increases until it reaches 80% humidity inside the duct.During this process the plant engineers need to know the temperature of the air after humidification, the flow of water necessary to maintain the required humidity.