X Incorrect Calculate the y-coordinate of the centroid of the shaded area. 45 mm 26 mm - 26 - 26 - mm mm Answer: y = i 28.4 mm

Q: The 283 kg horizontal steel bar is suspended by the three springs. The stretch of each spring is 126…

A:

Q: What is the complete specification of a nut having a stress area of 0.170 in? (standard size) that…

A: 1/2"-28UNEF-3B-LH

Q: 1. A reservoir contains 2.83 cubic meters of CO at 6895 kPa and 23.6 deg. Celsius. A cylindrical…

A:

Q: 3. A 2-mm-diameter and 10-m-long electric wire is tightly wrapped with a 1-mm-thick plastie cover…

A:

Q: The 0.25 kg slider A is pushed along the circular bar by the slotted bar. The circular bar lies in…

A:

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

A:

Q: Resolving power of an spectroscopic instrument is increased when...

A: Resolving the power of spectroscopic as the minimum wavenumber, frequency or the wavelength which is…

Q: An electrical wire with a length of 5-m and 3.5-mm-Ø spreads over one room at 18°C. Heat is…

A:

Q: 2. A cord is wrapped around a homogeneous disk of radius r = 0.5 m and mass m = 14.25 kg. If the…

A:

Q: 4. A reheat-regenerative cycle is use in a steam power plant. The steam is first reheated and then a…

A:

Q: An Actual Reheat Cycle with one-stage reheating is executed with steam expanding initially from the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: By the method of this article, determine the rectangular and polar radii of gyration of the shaded…

A:

Q: Why we measure flow? choose among the choices. you can choose multiple/more than one answer if…

A: Flow measurement is necessary for the custody transfer of high-value raw fluids like petroleum.  For…

Q: A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform…

A:

Q: Two forces L (parallel to the y-axis) and A (parallel to the z-axis) are applied at point Q on the…

A:

Q: A tripod supports the load W as shown in the figure. Determine the maximum load "W" (in pounds),…

A:

Q: For the beam cross-section shown, (a) find the maximum bending stresses of the beam if the bending…

A:

Q: the system shown starts from rest in the position shown. when block A hits the floor the cable…

A:

Q: How can you apply the concept of linear combination in engineering

A: Given question: How can you apply the concept of linear combination in engineering?

Q: What horsepower is required to isothermally compress 800 ft3of air per minute from 14.7 psia to 120…

A: Given data, Isothermal Compression V1 = 800 ft3/min  ( V1 = Initial volume ) P1 = 14.7 psia (P1=…

Q: SITUATION 8 Determine the critical hydraulic gradient of a coarse- grained soil if buoyant unit…

A:

Q: 3. Find the moment of inertia about X-X axis. 6 in. 0.5 in. 4 in. 0.5 in. K

A: find the moment of inertia about x-axis.

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: What are the general sources of error when using Vernier Caliper? when using Micrometer Caliper?

A:

Q: 9.6 - Perform the following reclassification:

A: To do :+ Reclassification

Q: Problem 4 A cylindrical pressure vessel with radius r =200 mm and wall thickness t =10 mm is…

A: INTRODUCTION : Hydraulic cylinders, cannon barrels, pipes, boilers, and tanks are examples of…

Q: The figure below shows the cross-section of a short rectangular column 300mm x 400mm. The column…

A:

Q: What horsepower is required to isothermally compress 800 ft3of air per minute from 14.7 psia to 120…

A: Given data, V1 = 800ft3/min P1 = 14.7 psia P2 = 120 psia Find work = W  = ?

Q: A flanged bolt coupling is used to connect a solid shaft 86 mm in diameter to a hollow shaft 100 mm…

A: INTRODUCTION : Flange coupling is the process of joining two shafts or tube ends in a flush, sealed…

Q: Initially, a closed system consists of 2 lb of water vapor at the temperature and volume of 300°F…

A: Given          Mass, m = 2 lb      Volume, V1 = 20 ft3                    V2 = 9.05 ft3 Work done, W…

Q: A circular plate 3 m diameter is Immersed in water in such a way that its greatest and least depth…

A: We know that a circular plate with a diameter of 3 m is immersed in water with a maximum depth of 4…

Q: A single extraction turbine operates on an ideal regenerative cycle, pressure and temperature…

A: To find

Q: A horizontal belt conveyor arranged as shown in the figure P1 below operates at a speed of 270 fpm…

A: When an amount of force act on the object, it has the tendecy to rotate the object about an axix…

Q: The roof of an airconditioned home is 7 m long, 9 m wide, and 20 cm thick. It is made of a flat…

A: find the cost of electricity.

Q: The coefficient of kinetic friction under block A in Fig. 24-A is 0.30 and under block B is 0.20.…

A:

Q: Which of the following choices is correct.1 regarding the right sequence of :combustion process…

A:

Q: describe the extration of elemental composition; s from solid sample. Explain what major concern of…

A: given; describe the extraction of elemental composition; s from solid sample. Explain what major…

Q: 9A converging–diverging nozzle operates at steady state. Air as an ideal gas with k = 1.4 flows…

A:

Q: viscosity and density of olive oil at 20C. use perrys table

A: To find Olive oil at 20 deg c

Q: b) For the truss structure in Figure Q4, determine the forces FAE, FAB and FCF acting in members AE,…

A:

Q: B G A C 5 m 4 m m 7 m GOO

A:

Q: Determine (a) the shear stress in the rivets and (b) the thickness "t" of the steel plate if the…

A: find the thickness of plate and shear stress in rivets.

Q: Given: P = 23 kN a 3 1.3 m b = 1.2 m c = 1.4 m d = 1 m 8 = 33° Required: DO NOT INCLUDE AN Y SIGN By…

A:

Q: 1. A rectangular beam120 mm wide by 400 mm deep is loaded as shown in the figure. a) Determine the…

A: Gievnb=120mmd=400mmw=3kN/mσb=10MPaL=5m

Q: Steam engine with incomplete expansion receives saturated steam at 1.04 Mpa, expands it to 0.105 Mpa…

A: Since you have posted a question with multiple sub-parts, and each subparts there are more than one…

Q: Would the volumetric flow rate in a pipe, assuming laminar flow, be more or less if the fluid were…

A:

Q: 1–24.An electric winch lifts a weight on the end of a 3-m jib pole. Determine angle 0 for the…

A:

Q: Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

A: find the centroid of the section and moment of inertia about centroidal x- axis.

Q: Provide a complete given and computation. Include all the decimals. In a reheat cycle steam at 8.0…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lbf/in2 and…

A:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.