In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless. The shaft rotates with a uniform angular velocity. The known belt pulls are indicated and the three pulleys are rigidly keyed to the shaft. If the working stress in shear is 64 MPa, determine the necessary diameter of a solid circular shaft. 3 kN 1 kN 250 mm -500 mm- 1 kN 1.25 kN 350 mm

In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless. The shaft rotates with a uniform angular velocity. The known belt pulls are indicated and the three pulleys are rigidly keyed to the shaft. If the working stress in shear is 64 MPa, determine the necessary diameter of a solid circular shaft. 3 kN 1 kN 250 mm -500 mm- 1 kN 1.25 kN 350 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
A 1.5-inch Monel shaft is used in a torsional application. Based on the operating speed of 100 rpm and factor of safety of 12. How much horsepower can it transmit? Assume the shearing stress is ¾ of the ultimate tensile stress which is 100 ksi.
A solid shaft is transmitting 15 MW of power at 1760 rpm. If the allowable shear stress must not amount to 500MPa, determine the size of the shaft.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft rotates at a speed of 679 rpm and transmits a power of 5 kW. If the maximum torque exceeds the mean torque by 23%. Take the value of allowable shear stress as 71 MPa. Find the value of the following i) Torque transmitted in N-m ii) Maximum torque transmitted in N-m iii) Diameter of the shaft in mm.
In the geared shaft shown below, gears A and B and gears C and D are separated by 500 mm. Gears B and C are separated by 400 mm. Gear A is experiencing a 250N⋅m250N⋅m clockwise torque; gear B is experiencing a 75N⋅m75N⋅m counter-clockwise torque; gear C is experiencing a 325N⋅m325N⋅m counter-clockwise torque; and gear D is experiencing a 150N⋅m150N⋅m clockwise torque. What is the absolute maximum shear stress in the shaft (in MPa) if the shaft has a 50-mm diameter?
If the allowable stress of a revolving steel is 150 MPa, what is the equivalent angular velocity which will produce such The mean diameter is 440mm.
A flange coupling is to be designed, using 6 bolts at a distance of 149mm from thecenter of the shaft, allowable shearing stress on the bolt is 103 MPa. If the shaft is totransmit 5485 hp at a speed of 1200 rpm, (a) determine the bolt diameter required inmm. (b) If the shaft is made of the same material as the bolt, determine the requireddiameter of the shaft in mm.
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
A conveyor belt is driven by a 8-hp motor turning at 2,500 rpm. Through a series of gears that reduce the speed, the motor drives the belt drum shaft at a speed of 18 rpm. If the allowable shear stress is 6.2 ksi and both shafts are solid, calculate (a) the required diameter of the motor shaft.(b) the required diameter of the belt drum shaft.
A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the shaft material is 56 N/mm2. Determine the diameter of the shaft?
A hollow shaft for a rotary compressor is to be designed to transmit a maximum of torque of 4750 N-m. The shear stress in shaft, if the ratio of the inside to the outside diameter is 0.4