Q A steel bar 50 cm long and 3 cm × 1 cm in cross-section, when it is subjected simultaneously to an axial pull of 50 kN and compressive stress of 100 N/mm² on its narrow edge, then the strain energy stored in a steel bar (in J, correct upto 1 decimal place) is [Take E = 2 × 105 N/mm² and μ = 0.25]

Q A steel bar 50 cm long and 3 cm × 1 cm in cross-section, when it is subjected simultaneously to an axial pull of 50 kN and compressive stress of 100 N/mm² on its narrow edge, then the strain energy stored in a steel bar (in J, correct upto 1 decimal place) is [Take E = 2 × 105 N/mm² and μ = 0.25]

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A mild steel wire of radius 0.5 mm and length 3 m is stretched by a force of 49 N. Calculate for the longitudinal stress, longitudinal strain, and elongation produced in the body if Young’s modulus for steel is E = 2.1 x 1011 N/m2. Answers: (6.238 x 107 N/m2, 2.970 x 10-4 m/m, 0.891 mm)
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2
The information in the photo attached shows elastic properties of a human tibula bone. If you were to take a small cuboidal cross section of the tibula bone and apply the ultimate shear stress, what would be the resulting strain? (a) 1.0 % (b) 6.7 % (c) 10 % (d) 15 % (e) None of the above.
Assume if the shear stress in steel exceeds about 4.00 108 N/m2 the steel ruptures. (a) Determine the shearing force necessary to shear a steel bolt 1.05 cm in diameter. (b) Determine the shearing force necessary to punch a 2.40-cm-diameter hole in a steel plate 0.530 cm thick.
rectangular steel plate, 1·2 m long and 850 mm wide, is subject to a compressive load along its length. If the width of the plate increases by 0·09 mm under load, determine its change in length. Take Poisson’s ratio for the steel as 0·28
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.
A 3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 kN. Poisson’s Ratio = 0.25 and E = 200 000 MPa. Compute the lateral strain. Express your answers in 6 decimal places.
Q1/A bar 500 mm long and 20 mm in diameter is elongated by 1.2mm under axial pull of 105 kN. Calculate stress and modulus of elasticity of bar.
12) For the given curved beam (as shown) with a rectangular cross section, calculate the distance of the neutral axis from the center of curvature. Express your answer in mm, up to 1 decimal place. 13) The bending moment acting on the curved beam with a rectangular cross section is 25 kN-m. What is the bending stress at point B? (Answer must be in MPa, up to 1 decimal place. Add a minus sign if the answer is a compressive stress.)
A 2 m long steel wire is fixed and hanging vertically with a tensile loadof 2 kN and causes it to stretch by 4 mm. Determine the diameter ofthe steel wire when the modulus of elasticity is 205 GPa.A. 3.5 mm B. 5.5 mm C. 4.5 mm D. 2.5 mm
A bar 500mm long and 200 mm in diameter is elongated by 1.2mm under axial pull of 105kn calculate stress and modulus of elasticity of bar