Q choose the correct answer: 1-Brushless excitation system consisting of.... a- Stator field winding and power diodes b-stator and rotor field winding and capacitor c- stator and rotor field winding and capacitor d- Everything mentioned in the options 2- Voltage generated per phase in an alternator is proportional to a-Flux per pole b-Number of turns in armature c- Winding factors d- Everything mentioned in the options e- Frequency of waveform 3- If input mech. Power of SG constant, the functionality of AVR is a- Control flux of rotor b-Control terminal voltage c- Control flux and terminal voltage d-Control Load angle

Q choose the correct answer: 1-Brushless excitation system consisting of.... a- Stator field winding and power diodes b-stator and rotor field winding and capacitor c- stator and rotor field winding and capacitor d- Everything mentioned in the options 2- Voltage generated per phase in an alternator is proportional to a-Flux per pole b-Number of turns in armature c- Winding factors d- Everything mentioned in the options e- Frequency of waveform 3- If input mech. Power of SG constant, the functionality of AVR is a- Control flux of rotor b-Control terminal voltage c- Control flux and terminal voltage d-Control Load angle

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 32RQ

See similar textbooks

Similar questions

DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC MACHINES Answer the following questions (A, B and C) depending on the topic. 1. ALTERNATORS A. Why is it necessary to maintain the speed of an alternator at all times and how do they control the speed of an alternator when in operation? B. Distinguish between half-coiled and full-coiled armature windings in alternators. C. Why are fractional pitch windings generally used in alternators?
9.a. The major failure area of a typical wound-field and wound-armature DC motor isA. a faulty commutator segment.B. open field windings.C. brush wear and failure.D. bearing failure.9.b. The magnetic material that's placed inside a coil of wire in a motor is called aA. concentrator.B. pole.C. form.D. rod.
a. Explain the terms, coil span, coil pitch, short pitching and chording of coils.b. Equalizer rings are needed in lap wound dc machines not in wave wound explain the reason andthe use of equalizer rings with the help of an example.c. What are dummy coils?d. What is the purpose of using short-pitched coils in ac windings?
2) the armature windings of a 12-pole DC machine are composed of 72 coils with 10 windings, and the windings are 5the layered wave is yellowish. The Rotor speed is 1000 rpm and the flux value per pole is 25mWb.Resistance of Armature windings, commutation windings and compensation windings is 70mΩ, 10mΩ and5mω. (a) the number of current paths in the machine, (b) the total number of conductors in Armature windings, (c) armature coefficient (constant)
Q2)A. Explain compound DC generator, also describe its types and terminal characteristics of compound DC generator. proper explanation and diagram
A separately excited generator has no-load voltage of 125V. A certain load rated at 1200W, 120V is then connected at the terminal. Calculate the series resistance needed to connect to the armature circuit in order for the load to operate at rated condition if the armature resistance is 0.0692Ω.
number of turns per phase? alternator induced voltage is? armature winding distrbution factor? voltage regulation? i need answer in 20 min
A 500-V, wave-wound, 750 r.p.m. shunt generator supplies a load of 195 A. The armature has 720 conductors and shunt field resistance is 100 Ω. Find the demagnetising amp-turns/pole if brushes are advanced through 3 commutator segments at this load. Also, calculate the extra shunt field turns required to neutralize this demagnetisation.
A shunt generator supplies a 31kW load at 230V through cables of resistance, R = 122mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =51mΩ. Determine the following below: The terminal voltage is, Answer and unit for part 1 The e.m.f. generated in the armature is,
A short shunt compound DC generator supplies a load current of 10A at a voltage of 10 volts. If the resistance of armature, shunt field and series field windings are 0.001 ohm, 1 ohm 0.00 ohm respectively. c) write down the factors to improve the generated voltage.
Identify the DC Generator used for Arc welding purpose. With a neat sketch explain its working. list its advantages & disadvantages??
22 The DC voltage is generated in the Armature winding of DC Generator. Select one: True False