Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive The supply voltage is v =300 sinωt , the supply frequency is 50 Hz and the load parameter values are: R =05 Ω, a) Sketch the diagram of electrical circuit b) Sketch the load voltage and current waveforms . c) Calculate the load current d) Calculate the average DC load voltage Vdc . e) Calculate the supply power to the loa

Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive The supply voltage is v =300 sinωt , the supply frequency is 50 Hz and the load parameter values are: R =05 Ω, a) Sketch the diagram of electrical circuit b) Sketch the load voltage and current waveforms . c) Calculate the load current d) Calculate the average DC load voltage Vdc . e) Calculate the supply power to the loa

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

(i) A fully-controlled single-phase bridge rectifier is supplied from a 50Hz, 220/120 V transformer .The rectifier supplying a highly inductive load of 10 Ohm resistor. For a firing angle of 45º, determine the rectified voltage, the rectified current and the power factor. (ii) If the current extinction angle β =200˚; Determine whether the current is continuous or discontinuous (iii) Sketch the appropriate load voltage and load current waveform
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive The supply voltage is v =300 sinωt , the supply frequency is 50 Hz and the load parameter values are: R =05 Ω, a) Sketch the diagram of electrical circuit b) Sketch the load voltage and current waveforms . c) Calculate the load current d) Calculate the average DC load voltage Vdc . e) Calculate the supply power to the load.
write down the formulae for 3-phase fully controlled,full wave rectifier with inductive load for the following parameters: Average DC voltagerms voltagepeak inverse voltagerms currentaverage DC currentefficiencyfiring angleextinction anglepower outputpower inputform factorripple factordistortion factortotal harmonic distortiondisplacement factorpower factor of rectifier. Please answer all subpart...
Consider the adjacent circuit diagram of three different rectifier topologies connected to an 346 Volt three-phase AC system. Assume a load resistance of 36Ω in ALL instances with NO losses in the rest of the circuit. Observe the connections to the AC supply and determine the parameters for, Rectifier A: 1) the maximum voltage across the load and the dc load voltage; 2) the r.m.s. load voltage and the rectification efficiency; 3 the r.m.s. current rating of the diodes and the conduction period of a single diode; 4 the PIV rating of the diodes
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
Design a +40 volt dc power supply for your sound system. Your sound system requires a 400 watt capability. The power supply is energized from a three-wire 110 Vrms 60 Hz power line that meets the National Electric Code (NEC). The system block diagram and design specifications are given below. Input is a 110 Vrms60 Hz. Output voltage is 40 volts, unregulated. Maximum allowable ripple is 2% Use a full-wave bridge rectifier. Use a transformer Assume diodes with VF= 0.7 volts Your design should include: Ø Well-labeled circuit diagram of what goes in the “Your Design” box. There should be enough detail such that someone could build an operational prototype. Polarities of key components are important Ø Key design equations and supporting calculations. Show your work! Ø Component specifications including: (a) Transformer-turns ratio (b) Effective value of the audio system load resistor (speaker impedance) and load current for a 400 watt, 40 volt…
A sinusoidal voltage of 48v, 60 Hz is applied to a half-wave rectifier with dynamic resistance of the diode of .001ohms turns ratio (3:1). Calculate the DC and RMS currents flowing through the load(R=210 ohms). Also calculate the dc output power developed, ac – input power supplied, rectification efficiency, and ripple factor.
2. An AC voltmeter uses a bridge rectifier with silicon diodes and a PMMC instrument with FSD = 75 µA. If the meter coil resistance is 900 Q and the multiplier resistor is 708 k2, calculate the applied rms voltmeter when the voltmeter indicates FSD.
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
1- A testing transformer 220 V/100 kV (rms), 50 Hz is supplying a half wave rectifier circuit. If the load resistance is 5 MΩ, find: a- The value of the smoothing capacitor so that the time constant is 10 times the supply periodical time. b- The rated peak inverse voltage (PIV) of the rectifier. c- The number of series connected rectifiers if the rated PIV of a rectifier is 20 kV. d- The ripple and the output voltages.
Three phase Bridge rectifier operated from a 380V, 50Hz source throughout three-phase Y/Y connected transformer with ration 2:1. The load current has continuous character with negligible ripples and average thyristor current of 15A. The circuit inductance per phase is 1.2mH. The rectified voltage due to overlapping angle is 90 % of that voltage when this angle is neglected. 1- How much will the voltage drop be due to circuit inductance * 2- How much will the dc average voltage Vdc(alpha) be. 3- How much will the firing angle be ? 4- The overlapping angle. 5- How much is the percentage change of the output dc power if the thyristors T2, T4 and T6 are replaced by three diodes D2, D4, D6. 6- How much will be the maximum RMS phase current for the mentioned in previous task circuit ( semi-converter). 7- If an additional of 1 mH inductances are added to the existing inductances in the phases , how much will the overlapping angle be. The dc load current is kept constant & the…