A single-phase bridge rectifier that supplies a very high inductive load such as a de motor is shown in Figure 3.9a. The turns ratio of the transformer is unity. The load is such that the motor draws a ripple-free armature current of I, as shown in Figure 3.9b. Determine (a) the HF of input current and (b) the input PF of the rectifier.

A single-phase bridge rectifier that supplies a very high inductive load such as a de motor is shown in Figure 3.9a. The turns ratio of the transformer is unity. The load is such that the motor draws a ripple-free armature current of I, as shown in Figure 3.9b. Determine (a) the HF of input current and (b) the input PF of the rectifier.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
What is the condition to obtain the maximum efficiency of a Rectifier? Neglecting the value of total resistance Neglecting the value of transformer resistance Neglecting the value of diode resistance Neglecting the value of load resistance
Q3: Determine ripple factor, form factor, available dc voltage, Transformer utilization factor, rectification efficiency, assume ideal diodes Vp=120sinwtTurn ratio=10:1
An ideal single-phase full wave rectifier circuit has a non-inductive resistanceload, negligible tube drops and no transformer losses. What is therectification or conversion efficiency in percent?
write down the formulae for 3-phase fully controlled,full wave rectifier with inductive load for the following parameters: Average DC voltagerms voltagepeak inverse voltagerms currentaverage DC currentefficiencyfiring angleextinction anglepower outputpower inputform factorripple factordistortion factortotal harmonic distortiondisplacement factorpower factor of rectifier. Please answer all subpart...
Below is a circuit containing a non-linear element;a) Determine the operating points (two) of the circuit in DC state?b) Find the resistance equivalent of the nonlinear element for the operating points you specified?c) For AC welding, find the instantaneous power of the nonlinear element (considering the element's equivalent resistance at the operating point)?
i) Draw the circuit diagram of the single phase full wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation. (ii) A single phase fully controlled bridge rectifier circuit has DC output voltage 175 V for an AC supply voltage of 210 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
Describe the design, Manufacturing and application factors that influence the following failure modes of integrated circuits: (i) electromigration; (ii) latched-up; (iii) electrostatic damage.
What are the different integrated circuits? Describe their characteristics, advantages and disadvantages.
Discuss the significance of Moore's Law in the context of microchips and semiconductor technology. How has the continuous scaling of microchips influenced their performance and energy efficiency over time?