Q. 2. (i) ate Kirchhoff's rules for an electric network. Using Kirchhoff's rules, obtain the balance condition in terms of the resistances of four arms of Wheatstone bridge. ii) In the meter bridge experimental set up, shown in the figure, the null point 'D' is obtained at a distance of 40 cm from end A of the metre bridge wire. If a resistance of 10 2 is connected in series with R₁, null point is obtained at AD = 60 cm. Calculate the values of R₁ and R₂.

Q. 2. (i) ate Kirchhoff's rules for an electric network. Using Kirchhoff's rules, obtain the balance condition in terms of the resistances of four arms of Wheatstone bridge. ii) In the meter bridge experimental set up, shown in the figure, the null point 'D' is obtained at a distance of 40 cm from end A of the metre bridge wire. If a resistance of 10 2 is connected in series with R₁, null point is obtained at AD = 60 cm. Calculate the values of R₁ and R₂.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Derive the Norton equivalent network with respect to terminals PQ for the network shown in Figure below and hence determine the magnitude of the current flowing in a 2Ὡ resistor connected across PQ
A Victoria plaza sub-station supplies 60kW to a load over 250 ft, 100mm2 , two conductors copper feeder, the resistance of which is 0.078 ohm per 100 ft. The bus bar voltage is maintained constant at 600V.Determine the load current
Using Norton’s theorem, calculate the current flowing through the 20Ω resistor in thecircuit shown in Figure Q1.
1. Why do we apply reduction factors in the design of electric equipment? Also, why do we increase the amperage for continuous loads? Give illustrations to further explain the point.
q) 150 kv single core cable has a radius of cable of 5cm. The insulation martial has two layers. The relative permittivity of the first and second layers are 6 and 3 respectively. If the minimum electric stress of the first and second layers are 30 kv/cm and 20 kv/cm respectively. Find the maximum electric stress of the first layer.note : subject is : power - underground cabel
An aluminum wire 7.5m long is connected in parallel with a copper wire 6m long. When a current of 5A is passed through the combination, it is found that the current in the aluminum wire is 3A. If the diameter of the aluminum wire is 1mm, determine the diameter of the copper wire. Assume the resistivity of copper to be 0.017µΩm and that of aluminum to be 0.028 µΩm. Major Topic 7 Factors that affect the resistance
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Flux Luman output per 200 W lamp Luman output per 500 W lamp Number of 500W lamps required Number of 220W lamps required Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
The student engineer of a campus radio station wishes to verify the effectiveness of the lightning rod on the antenna mast (as shown). The unknown resistance Rx is between points C and E. Point E is a true ground, but it is inaccessible for direct measurement because this stratum is several meters below the Earth’s surface. Two identical rods are driven into the ground at A and B, introducing an unknown resistance Ry. The procedure is as follows. Measure resistance R1 between points A and B, then connect A and B with a heavy conducting wire and measure resistance R2 between points A and C. (a) Derive an equation for Rx in terms of the observable resistances, R1 and R2. (b) A satisfactory ground resistance would be Rx < 2.00 Ω. Is the grounding of the station adequate if measurements give R1 = 13.0 Ω and R2 = 6.00 Ω? Explain.
A 3-wire d.c. distributor, 250 m long, is supplied at end P at 500/250 V and is loaded as under : Positive side : 20 A, 150 m from P ; 30 A, 250 m from P Negative side : 24 A, 100 m from P ; 36 A, 220 m from P The resistance of each outer wire is 0·02 Ω per 100 m and the cross-section of the middle wire is one half that of the outer. Find the voltage across each load point.
In a concentric spherical electrode system at the optimum geometry with regard tobreakdown the outer radius is r2 = 50 cm. The insulator breakdown strength is Eb = 30 kV/cm.a) For the optimum geometry with regard to breakdown calculate the inner radii (r1)b) Calculate the breakdown voltage (Vb)c) If the applied voltage is U = 300 kV, find the values of inner radii (r1) where nobreakdown occurs. Also sketch the Emax with respect to r1 and show all of thedischarge events (partial discharge, no breakdown, complete breakdown).
(a) What are the voltages at vC1 and vC2 in the circuitas shown = −1.6 V, IEE = 2.5 mA,RC = 600 , and VREF = −2 V? (b) Redesign IEEand RC in the current switch described in part (a)to operate at one-tenth of the power with the samevoltages.