Q. 6: A steel rod 20 mm in diameter, 400 mm long is co-axially enclosed in brass tube of 25 mm external diameter and 2 mm thickness with 400 mm length. Determine the stress induced in each material and the change in length of the assembly if it is subjected to an axial compressive force of 5R kN. The rod and tubes both are clamped at their ends. Esteet-200 GPa and Ebrass-100 GPa

Q. 6: A steel rod 20 mm in diameter, 400 mm long is co-axially enclosed in brass tube of 25 mm external diameter and 2 mm thickness with 400 mm length. Determine the stress induced in each material and the change in length of the assembly if it is subjected to an axial compressive force of 5R kN. The rod and tubes both are clamped at their ends. Esteet-200 GPa and Ebrass-100 GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two fork end pieces are to be joined together by a single steel pin of 25mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?
A copper wire 2.0 m long, hanging vertically, supports a load of 6.0 kN.Neglecting the weight of the wire, determine the required diameter ifthe stress is not to exceed 300 MPa and the total elongation is not toexceed 5.0 mm. Assume E = 125 GPa.Answer: d = ___________________
Question- 1) Two gage marks are placed exactly 270 mm apart on a 10-mm-diameter aluminum rod with E = 72 GPa and an ultimate strength of 150 MPa. It is Know that the distance between the gage marks is 270.28 mm after a load is applied, determine the stress in the rod
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
The steel tie bar shown is to be designed to carry a tension force of magnitudeP=120 kN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel tobe used, the maximum allowable stresses are σ =175 MPa, τ =100 MPa,and σb=350 MPa. Design the tie bar by determining the required values of(a) the diameter d of the bolt, (b) the dimension b at each end of the bar, and(c) the dimension h of the bar.
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E= 15,000 ksi] rods, and a solid steel [E= 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.625 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.375 in. If all bars are unstressed before the load P is applied, determine the normal stresses in the bronze and steel rods after a load of P= 14 kips is applied.
The boom AB is made up of a hollow square 80-mm tube having a wall thickness of 2 mm. A 20-mm diameter steel cable BC and a 16-mm diameter pin at A support the boom in the position shown. The working stresses are 140 MPa for the cable, 110 MPa for the boom, and 70 MPa for shear in the pin. Neglecting the weight of the boom, determine the largest safe load W that can be applied as shown.
Two gage marks are placed exactly 250 mm apart on a 12-mm-diameter aluminum rod with E5 73 GPa and an ultimate strength of 140 MPa. Knowing that the distance between the gage marks is 250.28 mm after a load is applied, determine (a) the stress in the rod, (b) the factor of safety.
A lever ABC is pinned at C and attached to a 12-mm diameter control cable AD. a. If the allowable tensile stress in the control cable is 140 MPa, what is the maximum safe value of the load P applied as shown in the diagram? b. What is then the shearing stress developed in the 20-mm diameter pin support at C? c. What is the bearing stress between the pin and the 25-mm thick support plates at C?
A copper rod is rigidly attached between a steel rod and a brass rod. Axial loads are applied at the positions indicated where F = 125 kN. Find the safe minimum value of diameter “d” that will not exceed a stress in steel of 780 MPa, in copper of 120 MPa, or in brass of 65 MPa.Answer: d = __________________
Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin.