Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is 2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bed slope is 1 in 1500, take n- 0.012.

Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is 2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bed slope is 1 in 1500, take n- 0.012.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A rectangular concrete channel 4.5 m wide is carrying water. At an upstream point, the depth of…

A: Given: Wide, b= 4.5 m Depth at upstream , d1 = 1.5m Depth at downstream,d2 = 1.17 m Length, L=…

Q: Determine the flow in a trapezoidal channel having base width of 4 m and side slope of 1:1 if the…

A: Given data: B=4 mdc=2.3 m Need to determine the flow of trapezoidal channel.

Q: Figure (4) Question (: The rectangular channel has a transition that causes its width to narrow to…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Using the geometry of Fig. prove that the most effi -cient circular open channel (maximum hydraulic…

A: The hydraulic diameter of flow through a channel can be expressed as, For the most efficient flow,…

Q: Consider uniform water flow in a wide brick channel of slope 0.4°. Determine the range of flow depth…

A: Step 1: The channel bed slope (S0) is given as: The roughness coefficient (n) of stream can be…

Q: A channel has a slope of 0.0004 m/m with n=0.015. It is expected that the channel will be able to…

Q: Q(1): A power canal of trapezoidal section has to be excavated through hard clay at least cost.…

Q: Compute for the specific energy of a rectangular channel having a flow of 1.8 cubic meter/sec. The…

A: Handwritten.jpg

Q: Water flows at a steady and uniform depth of 2 m in an open channel of rectangular crosssection…

A: Given data as per question depth = 2 m base width = 5 m slope = 1 in 1000 Manning’s roughness…

Q: Water flows in a triangular V-notch steel channel, with vertex angle of 60°, at a velocity of 1.2…

Q: At what depth will water flow in a 4 m wide rectangular channel if n=0.018, S0=0.0009, and Q=7m^3/s?

A: Givenb=4 mn=0.018S=0.0009 Q=7 m3/s

Q: A contacted weir is to be built in a rectangular channel 3m wide dis haring a quantity of 225…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: For the channel shown, the top water width is y 45° 45° в

Q: 5. A rectangular flume made of planed timber(n=0.12) has a slope of 1m per km. If the flume will…

Q: 2) A venturi flume is placed near the middle of a long rectangular channel with Manning's…

A: The value of Manning's coefficient is n=0.012 m-1/3s. The width of the channel is w=5 m. The…

Q: A channel is formed by having two vertical brick walls with a semi circular culvert at the bottom.…

A: As per the guideline, I can solve only first question. For second question, repost in a separate…

Q: At what depth will water flow in a 4m wide rectangular channel if n= 0.018, S0 = 0.0009 and Q

A: GivenQ=7m3/sn=0.018 So=0.0009

Q: At what depth will water flow in a 4m wide rectangular channel if n= 0.018, S_0 = 0.0009 and Q =…

A: Given details: S0=0.0009n=0.018b=4 mQ=7 m3/sec Formula used: Q=1nAR2/3S01/2

Q: For the channel of (Consider a rectangular channel 3 m wide laid on a 1°slope. If the water depth is…

A: Given data b=3 md=2 m

Q: A rectangular cross sectional area of channel having width 4 m and depth 7.7 m. With help of these…

A: Given data : Width of channel b=4 m Depth of water h=7.7 m Required : Wetted perimeter

Q: Water flows uniformly in a finished-concrete rectangular channel with a bottom width of 0.85 m. The…

A: Given Data: Bottom width of channel is b = 0.85 m. The flow depth is y = 0.4 m. Bottom slope is S0…

Q: Consider the same rectangular channel as in the previous problem (4.0 m wide, filled with water to…

A: Calculate the flow rate by Mannings equation Q=1.49×A×R23×S12n Where A = Area R = Hydraulic…

Q: A trapezoidal weedy excavated earth channel has a bottom slope of 1°, base width of 5 m and a side…

Q: A cast iron V-shaped water channel shown, has a bottom slope of 0.5°. For a flow depth of 0.75 m at…

A: Mannings Equation Q=1.46×A×R23×S12n Calculate Cross-sectional area…

Q: If the channel (Consider a rectangular channel 3 m wide laid on a 1°slope. If the water depth is 2…

A: Given data: Wide (b) = 3 m depth (h) = 2 m manning factor (n) = 0.020 slope (S) = 10= 1: 57.29 =…

Q: Draw and label a hydraulic jump (in a channel of constant width). (a) Indicate regions of…

A: Hydraulic jump Hydraulic jump usually maintains the high water level on the downstream side. This…

Q: Problem 16.10 Find the discharge through a rectangular channel of width 2 m, having a bed slope of 4…

Q: A trapezoidal channel having a bottom slope of 0.001 is carrying a flow of 30 m/s. The bottom width…

A: A trapezoidal channel having a bottom slope of 0.001 is carrying a flow of 30 m/s. The bottom width…

Q: Find the velocity of flow and rate of flow of water through a rectangular channel of 6 m wide and 3…

A: Given:

Q: A circular corrugated-metal water channel has a slope of1:800 and a diameter of 6 ft. (a) Estimate…

A: The area and hydraulic radius are given in the text:…

Q: Problem 1. A 4 m wide channel with a rectangular cross-section is carrying a flow with flow rate Q =…

A: Froude number (Fr) is a dimensionless number. Froude number (Fr) is defined as ratio of the inertia…

Q: The discharge through a rectangular channel of 20 m wide is 50 m/s. The depth of flow is 1 m. The…

A: Y = depth of flow Z = elevation of bed H = E + Z = total energy Differentiating total energy line…

Q: Water flows over a spillway of a dam. At the bottom of the spillway, water flows into a rectangular…

A: Using Manning's equation; Q = A 1n (Rn)23 (S)12 ..........(1) ; where, A = area, b X…

Q: A rectangular channel is 2 m wide and contains water 3 mdeep. If the slope is 0.85° and the lining…

A: Given data: Width of the rectangular channel, b = 2 m. Depth of water, y = 3 m. The angle of…

Q: A rectangular channel, laid out on a 0.5° slope, delivers afl ow rate of 5000 gal/min in uniform fl…

Q: A trapezoidal open-channel (n=0.015) has a side slope of 5H:2V and a bottom width of 2.5m. The flow…

Q: Consider a rectangular channel 3 m wide laid on a 1°slope. If the water depth is 2 m, the hydraulic…

A: Given data⇒b=3md=2m

Q: What will be the depth of flow in a trapezoidal concrete-lined channel that has a water discharge of…

A: given data: n=0.012 slope(S)=1/10

Concept explainers

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing. 

Question

X=48

Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is
2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bed
slope is 1 in 1500, take n- 0.012.
Use Value of X (Base width) from following table

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At what depth will water flow in a 4 m wide rectangular channel if n=0.018, S0=0.0009, and Q=7m^3/s?
A triangular open-channel (n=0.014) has a side slope of 2H:1V. The flow depth is 3m when the slope is 0.002. Determine the volumetric flowrate.
What will be the depth of flow in a trapezoidal concrete-lined channel that has awater discharge of 1000 cfs? The channel has a slope of 1 ft in 500 ft. The bottom width of thechannel is 10 ft. and the side slopes are l vertical to 1 horizontal, n=0.012
Question 1 Find the conjugate depth of a hydraulic jump in a horizontal channel if the upstream depth is 0.8 m and the velocity of the flow is 8 m/s.
Compute for the critical depth in a channel with constant spesific energy of 5cm in a channel with 2.5 width and flow of 2m/sec
In flowing from section (1) to section (2) along a rectangular open channel, the water depth decreases by a factor of three and the Froude number changes from a subcritical value of 0.7 to a supercritical value of 3.4. Determine the channel width at (2) if it is 8 ft. wide at section (1). Assume stead-state flow.
A circular corrugated-metal water channel has a slope of1:800 and a diameter of 6 ft. (a) Estimate the normal discharge,in gal/min, when the water depth is 4 ft. (b) For thiscondition, calculate the average wall shear stress.
Water at 10°C flows in a 6-m-wide rectangular channel at a depth of 0.55 m and a flow rate of 12 m3/s. Determine (a) the critical depth, (b) whether the flow is subcritical or supercritical, and (c) the alternate depth
Water at 65°F flows at a depth of 1.4 ft with an average velocity of 10 ft/s in a wide rectangular channel. Determine (a) the Froude number, (b) the critical depth, and (c) whether the flow is subcritical or supercritical. What would your response be if the flow depth were 0.2 ft
Consider the same rectangular channel as in the previous problem (4.0 m wide, filled with water to 6.0 m, and walls of corrugated metal). If the slope is 0.65°, estimate the volume flow rate of the water.
Water flows uniformly in a finished-concrete rectangular channel with a bottom width of 0.85 m. The flow depth is 0.4 m and the bottom slope is 0.003. The channel should be classified as (a) Steep (b) Critical (c) Mild (d ) Horizontal (e) Adverse
A trapezoidal channel having a bottom slope of 0.001 is carrying a flow of 30 m/s. The bottom width is 10.0 m and the side slopes are 2H to 1V. A control structure is built at the downstream end which raises the water depth at the downstream end to 5.0 m. Compute the water surface profile till 1.20 m. Manning n is 0.013 and a = 1. Select an appropriate Month for your calculations. Please read the question carefully and provide the correct solution with simple steps fast. Please answer quickly.