Q.1- Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d, and d and if E1-80 GPa and E2-120 GPa, what will be total change in the length of the roads, (AL)? -4 DAN k Fig. P1.1 and P1.2

Q.1- Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d, and d and if E1-80 GPa and E2-120 GPa, what will be total change in the length of the roads, (AL)? -4 DAN k Fig. P1.1 and P1.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A nylon thread is subjected to a 9.29-N tension force. Knowing that E = 3.22 GPa and that the length of the thread increases by 1.17 %, determine the diameter of the thread in μm. Express your answer in four decimal places.
A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for compression parallel to the grain σC = 8.3 MPa and a modulus of elasticity E = 11.1 GPa. Using the allowable-stress method, determine the largest allowable effective length L that can be used. Take P = 88 kN. (Round the final answer to two decimal places.) The largest allowable effective length L that can be used is m.
Determine the length (in meters) of the shortest 2-mm diameter bronze wire, which can be twisted through 3 complete turns without exceeding a stress of 88 MPa. Use G = 37 MPa.
For the riveted connection shown, the allowable shearing stress in the 25mm rivets is 140MPa. Assume the plates are adequate to transmit the load to the rivets. P = 60 kN.a. Determine the shearing stress in the most stressed rivet.b. Determine the maximum allowable value of P.c. If P = 80 kN, determine the minimum diameter of rivets.
The cantilever beam AB will be installed so that the 60-mm side forms an angle β between 0 and 90° with the vertical. The 660-N vertical force P is applied at the center of the free end of the beam. Determine the value of β for which the normal stress at point a is a maximum and the corresponding value of that stress. (Round the final answer to two decimal places.)
The change in diameter of a large steel bolt is carefully measured as the nut is tightened. Knowing that E= 29 *106 psi and ν= 0.30, determine the internal force in the bolt if the diameter is observed to decrease by 0.5 *103 in
The rod ABCD is made of an aluminum for which E = 70 GPa. Take P = 75 kN. a) For the loading shown, determine the displacement of point B. b) Determine the displacement of point D.
Consider the loading shown. The allowable normal stress for the steel used is 172 MPa. For the selected design, determine the maximum value of the principal stress σmax at the junction of a flange and the web. (Round the final answer to one decimal place.)
The lap joint shown is connected by 6 pieces rivets. Assuming that the load P = 70 KN is carried equally by the six rivets.Determine the diameter of the rivets if the allowable shear stress is 148.54 MPa.
A uniform concrete slab of total weight W is to be attached as shownto two rods whose lower ends are on the same level. Determine theratio of the areas of the rods so that the slab will remain level. Answer: Aal/Ast___________________
Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of polystyrene 6.07 mm thick, knowing that the force exerted by the punch is 38.9 kN and that a 54.4-MPashearing stress is required to cause the material to fail. Round off the final answer to two decimal places.
Solve Prob. 4.75 when θ = 30° and P = 150 N.