Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Determine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. .B. What force is required to punch a square hole (25-mm*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN/m2. Puncher 25 mm * 25 mm 30 mm thick.

Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Determine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. .B. What force is required to punch a square hole (25-mm25mm) in a plate that is 30 mm thick? The shear strength is 350 MN/m2. Puncher 25 mm 25 mm 30 mm thick.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The belt shown has a width of 43 mm and a thickness of 6 mm. [P1= 30 kN, P2= 6 kN, P3= 14 kN, P4= 14 kN] A-What is the maximum internal force in the belt? B-What is the cross sectional area of the belt? C-What is the maximum normal stress in the belt?
A 60-inch length of 2-inch OD x 1/8-inch wall 2014-T4 aluminum tube is supported by pinned supports at A and B as shown below. A 48-inch long pipe wrench is placed over the end of the tube at C as shown in the right view. (a) If a 200-lb person puts their full weight F on the end of the wrench handle will the tube material reach its yield point in shear? Use the maximum shear stress theory and show all calculations. (b) Where along the length of the tube, and in the tube cross-section, will the point of maximum shear stress be located? Be specific.
A steel flat 10 cm wide and 2 cm thick is bent into a circular arc of 50m radius.Find the maximum intensity of stress induced. Take E = 2.05 * 10 ^ 5 N/mm².
A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 39 ksi, determine the minimum force P (in kips rounded to the nearest tenths) required to punch the slot. Assume d = 0.75 in. and a = 4.00 in.
q1=150 Mpa, q2=40 MPa Calculate the stresses σx,σy,σz and deformation εz1,εz2 in the z direction.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding.
PLEASE ANSWER ASAP TY! a) Determine the cross-sectional area of the structural tube (in mm2) b) Determine moment of inertia of the cross-section about the neutral axis (in mm4) c) What is the maximum normal stress at point K (in MPa)? Include negative sign if compressive. d) What is the axial stress at section H-K (in MPa)? Include negative sign if compressive. e) What is the flexural stress at section H-K (in MPa)? f) What is the maximum normal stress at point H (in MPa)? Include negative sign if compressive.
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate. Answer a and b please
Determine normal stress across plane passing through 50 degree to the plane 100 N/mm2
A steel column of hollow circular cross section is supported on a circular steel base plate and a concrete pedestal . The columm has outside diameter d = 250 mm and supports a load P= 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness ? Based upon your result, select a thickness for the column. (Select a thickness that is an even integer, such as 10, 12, 14,... in units of millimeters.) (b) If the allowable bearing stress on the concrete pedestal is 11.5 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load P that the column with the selected thickness can support?
QUESTION: The distributed load on the T-section beam shown below and moment affects. A is the fixed joint and B is the sliding joint. This beam is made of a ductile material with a yield stress (σak) of 1000 MPa. The thickness (depth) of the beam profile is t=6 mm. A) As a mechanical engineer, check the strength of this beam (in terms of Normal and Shear Stress) ? B) In order for the existing beam to run smoothly, two 100x25 mm plates made of the same material are planned to be welded to this beam. The mechanical engineer working in the factory told the welder to weld this piece under the beam (where the B point is). But the welder, regardless of what the mechanical engineer said, welded this plate to both sides of the existing T-section beam as shown below, thinking that it wouldn't matter anyway. As a mechanical engineer : 1) After welding these plates on both sides of the beam, as the welder did, find out whether the new beam will work smoothly or not by making the necessary…
In the shown diagram below, the curved out bar has an axis that is circular (with mean radius r = 12in) and is subjected to the m horizontal forces P = 400lb at the two ends. The cross-section of the bar is a triangular shape with height h and thickness t. If the allowable tensile stress in the bar is 12,000 psi, and height h=1.2 in, what's the minimum thickness tmin that is required?