Q.2 A generator is connected to a transmission line as shown below. Calculate; a) VSWR b) The reflection coefficient at the load c) The input impedance of the line d) Find and plot the magnitude of the voltage as a function of z along the transmission line. 10V 5092 Zo=5022 -1.5λ ZL=80-j4092

Q.2 A generator is connected to a transmission line as shown below. Calculate; a) VSWR b) The reflection coefficient at the load c) The input impedance of the line d) Find and plot the magnitude of the voltage as a function of z along the transmission line. 10V 5092 Zo=5022 -1.5λ ZL=80-j4092

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Find the steady-state value of the following system to a unit step input. Note: we are talking about…

Q: what is the main physical phenomenon that has an adverse effect on the am signal?how can this…

A: The physical phenomenon that has an adverse effect on AM Signal is known as Amplitude fading (or)…

Q: For the low-pass filter depicted below find the value of the capacitor C in μF, that provides…

A: Given circuit: Resistance, R=240 Ω and, Critical frequency fc=60 Hz.

Q: SOLXE FOR IB. Ic, I Xce, VB, VC, VE, te

A: In this question We need to determine the all unknown current and voltage. We know Voltage VBE =…

Q: [PL1a & PL.1c] Find It (s).

A: The given input current is in time domain and the same can be converted into s domain by using the…

Q: A factory has an average daily load of 200 kW and a maximum demand of 250 kW. The factory operates…

A: In this question We need to determine the load factor of the factory. We know Load factor is define…

Q: C₁ 캬 10 μF R₁ 10 ΚΩ J2 R₂ 2.2 ΚΩ hFE (ave) Vcc +15 V = Rc 1.2 ΚΩ J3 J1 2N3904 RE 470 Ω Co +/6 10 μF…

A: We need to find out the base to collector voltage for given circuit.

Q: The figure below shows a stepper motor. Determine the step angle for Full and Half stepping…

A: Solution: Step Angle = 360°Number of stator phases × number of rotor teeth

Q: Three charges q₁ = -3Q, q2 = +3Q and q3 = -60, each at a distance of 'd' from the origin is placed…

Q: A balanced A-connected load is fed by a three-phase supply for which phase b is open circuited as…

A: Given- A balanced ∆ connected load is fed by a 3-phase supply. Ia=8∠0° AIb=0Ic=8∠180° A. To find-…

Q: Problem 3 Consider the following circuit: 392 192 5Ω 292 492 12 V (a) Carefully identify series and…

A: Dear Student, Since you have posted a question with multiple sub parts, we will provide the solution…

Q: 8. A nonmagnetic medium has an intrinsic impedance 240e/6. Find its complex permittivity.

Q: Given a = 11, b = 4, c = 1, d = 2, e = 3, f = 1, g = 4 and h = 1, in the circuit below, obtain Vo…

Q: how to derive this formula? Bdc= Ic/Ib=hFE

A: Derive the given formula: IB=IE1+β Where: IE= emitter current IB= Base current IC= Collector…

Q: 1. What energy audit instrument is used to measure flow of water in a pipe. A, Bourdon Gauge B.…

A: A. Bourdon gauge is used the measure the pressure of all kind of liquid and gasses it can measured…

Q: Problem 1 Consider the op-amp circuit shown below 100F yin a) Choose the resistors R1 and R2 and R3…

Q: 2. A 20 KVA, 2500/250 V, 50Hz, single-phase transformer gave the following test result: Open-circuit…

Q: Consider the circuit below. The voltage on the capacitor C₁ at t = 0 is 100 kV and the voltage on…

A: The ac circuit is given as The initial voltage of capacitor C1 is VC10-=100V

Q: DE NG 4. Discussion: Phase Lead Compensator Prove mathematically the effect of compensator at the…

A: Given: Phase Lead Compensator.To prove: The effect of compensator at the system and its comparison…

Q: Problem 3 For the following radiation intensity functions (0 ≤0 ≤ 1,0 ≤ ≤π), find the directivity…

Q: A 220 V, 50 Hz, 6-pole star-connected alternator with, ohmic resistance of 0.06 22/ph, gave the…

A: Given data Armature current/Load current; Ia=IL=ISC=40 A Armature resistance; ra=0.06 Ω Power…

Q: Question-1 1 Consider the following circuit where l (t) = 5e-³ sin(2t) u(t) A. 0₁ 1 In C [PL.la &…

A: In this question we need to find the input current in S- domain we use Laplace transform

Q: Find Iy, using the superposition method. The circuit is in the attached image.

Q: A 3-phase, 16 pole alternator has a wye connected armature winding with 144 slots, 10 conductors per…

Q: 6. If a 100V DC battery supplies a resistor and an uncharged capacitor, determine the voltage across…

Q: 6) G(s) = S-1 s²-5s+5 a) Determine and draw the poles and zeros b) Determine the possible ROCs. c)…

A: In this question we need to find the following Determine and draw poles and zeros Possible ROC…

Q: Question-2 Consider the following circuit where R₁ = 300 and R₂ = 100. Vin Given that: Vin (s) = =…

Q: VZ-240, FIND: Vbn van Van=300/30 VZO Vab VZ-120 b a 2+j3 faz B LAB 2 IBC Z ICA Z 10-js C

A: it is asked to find Vbn, Vcn, Vab for given 3 phase system

Q: QUESTION 2 Solve for Vo in (V). Use complete diode model and forward resistance of 5ohms + ID 6 V Si…

A: In this diode circuits we need to find Vo (Q2) current through R=4.7kohm (fig:a) Circuit (Q2)…

Q: Find total load power Provide answer asap. I will rate Positively

A: Since the given circuit is balance we can analysis the 3phase circuit on phase basis. Now we draw…

Q: A (0 – 600) V range voltmeter has inaccuracy of ± 2% of its full scale. Calculate the % errorin…

Q: Note: All question solutions should be A: Determine vo and i in the circuit showr 12 V 4592 ww 692…

A: Given data, Circuit diagram is given as,

Q: Show that a system of differential equations that describes the currents i(t) and i3(t) in the…

Q: En el circuito ilustrado, encontrar el valor de lx O 0.3456 W -0.3456 W O 10 MA O-10 mA 24 mA 5 k 2…

Q: b) Find the Thévenin equivalent of the circuit in Figure 3.126. R₁ V R₁ R₂ R3 LA | I A'

Q: Derive an equation for linear signal conditioning that will convert a sensor output voltage in…

A: I have written this solution as handwritten solution. Hope you find the solution clear.

Q: Problem 2: Use any analysis technique of your choice to find i(t) in the circuit below. 1.25 F…

Q: For the circuit shown in the Figure find the node voltages v, and v, using r 492 www 2 V 22 22

A: Circuit is given as:

Q: An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the…

A: Solution: Given data in question Number of Pole = 8 load current = 295 A Field current = 5 A

Q: What is coupled magnitudes? What is the significance of this difference in the coupled magnitudes to…

A: We need to define coupled magnitudes.Also, to explain the significance of the difference in the…

Q: Find lo using nodal analysis; Answer: Io = -3.86mA 6V 1+ www 6 ΚΩ I 6 ΚΩ 4 ΚΩ Το + 24V

A: Given data, The circuit is,

Q: What is an open ended signal?

A: To define: Open ended signal.

Q: Question: An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of…

A: Given data, A lap wound DC shunt generator with, Number of Pole, P = 8 Number of parallel path, A =…

Q: c) A controlled system is shown in Fig. Q3(c). Calculate the range of gain, K for a stable system.…

Q: Referring to the circuit in the figure and given that R₁= 100 KQ, R₂= 1 KQ and C=200 mF, find the…

A: here we have to find the output voltage for the input conditions.

Q: Determine Q-point for the diodes in the circuit given below using the constant voltage drop model…

Q: How did you find the angles? Also my computer says the answer to (a.) is incorrect.

A: The angles can be calculated using rectangular to polar conversion i.e., x+jy=x2+y2∠tan-1yx

Q: (3) Determine the initial value of the function f(t), where: S 4s (b) F(s) = -2s² +9s+6 (a) F(s) =…

A: Given data, Function is given as, (a) F(S)=s2s2+ω2 Initial value of f(t) can be find using initial…

Q: For the following block diagram, find the closed loop transfer function: R K1 F(s) + + G(s) K2

A: In this question We need to determine the closed loop transfer function. We are solving this…

Q: Question 1 For the Gaussian pulse example, determine the AT using the "full width at 0.1 of the…

A: Answer : Given information written below. For the Gaussian pulse example, it is asked to determine…

Question

Q.2 A generator is connected to a transmission line as shown below. Calculate;
a) VSWR
b) The reflection coefficient at the load
c) The input impedance of the line
d) Find and plot the magnitude of the voltage as a function of z along the transmission line.
10V
5092
Zo=5022
-1.5λ
ZL=80-j4092

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Transmission Line Parameter and Scattering Parameter (S-parameter)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A transmission line of characteristic impedance 40 ohms and length 6.2λ is terminated by an unknown load impedance. The reflection coefficient, Γ, looking into the transmission line at the input is 0.45+j0.55 What is the unknown load impedance?
5 (a) With an aid of a simple diagram explain the construction of a coaxial cable (b) If a load of 50 Ohms terminates a transmission line of impedance 100 Ohms calculate the reflectance and the amplitude of the reflected wave (given a unit amplitude incident wave). Also find the VSWR in this case (c) A 50Ω transmission line is connected to an antenna with load impedance of ZL = (25-j50) Ω. Design a short-circuited parallel stub required to match the lines. (Use a smith chart and upload it along with your answers)
A generator is connected to a transmission line as shown below. Calculate; a) VSWR b) The reflection coefficient at the load c) The input impedance of the line d) Find and plot the magnitude of the voltage as a function of z along the transmission line.
Characteristic impedance of a lossless transmission line is 90 phn. The capacitance per unit length for the line is 1.5 mF/m. Find out the inductance per unit length for the line.
The magnitude of the phasor voltage on a lossless air transmission line connecting a transmitter to a reci=eiver is shown below. The transmission line impedance is 50 ohms. The sinusoidal generator operates at a frequency of 3 GHz. The load is at position z = 0. The first minima at point A (|V|_min = 0V) occurs at d = 1.25 cm from the load towards the generator. a. What is the Voltage Standing Wave Ratio (VSWR) of this line? What is the reflection coeddicient a the load in phasor format (magnitude and phase)? b. What is the physical distance from point C to D in meters? c. What is the magnitude of the reflection coefficient |Γ (at C)| at point C? d. What is the wave impedance (resistance and reactance) and the reflection coefficient (phase and magnitude) at point C.
A lossless transmission line has a Zo of 50 ohms and a line velocity of 2.4 x 10^8 m/s. If the operating frequency is 1 MHz. Determine the capacitance in pf.
An antenna has an input impedance of 73 + j 10 ohms. If it is directly connected toa 50 ohm transmission line, find the reflection coefficient, VSWR and return loss.
Since a 50 ohm transmission line with phase constant (π/10) rad/m will be used at 500 MHz, what is the inductance of the line per unit length, in nH/m?
9. Assume a transmission line with ZL = 85 + j45 Ω and Zo = 30 Ω. If the frequency of the line is 1.5GHz, use the Smith Chart to find: i) the reflection coefficient; ii) the distance to the first voltage maximum; iii) the voltage standing wave ratio; iv) the admittance of the load; v) the position of the short-circuited stub on the main line for a perfect impedance matching; vi) the length of the short-circuited stub. (Show all steps on the Smith chart)
A short-circuited transmission line section is exactly one-quarter wavelengthat a frequency of 1250 MHz. Calculate the inductave reactance , and (b) the eq uiva le nt inductance, at a frequency of 500 MHz. The character st ~ impedance of the line is 50ohm
If the amplitude of the input reflection coefficient is 0.5 with an angle of 45 degrees and the length of the transmission line is I= 0.15A, find the impedance of the load. (Z0=50ohm) Zin =? SWR=? YL=? ZL=?
A transmission line has a characteristic impedance of 100 ohm and a resistance of 0.2 ohm/m. If the line is distortion less, then what will be the attenuation constant associated with the line?