Q.3 Answer only Four of the following1) If The AC Maxwell Inductance Capacitance Bridge has the following constants:R var = 5 kn, C, = 0.2 µF, R2 = 2.5 kn, and R3 var = 2 kN at frequency 1 kHz.Determine the unknown resistance, inductance and Q-factor of the bridge circuit.2) Draw the block diagram of cathode ray oscilloscope and give a reason why should weuse the delay line circuit after the vertical amplifier block? Could we cancel it?3) Show the difference between AC voltmeter using HWR and AC voltmeter using FWR.[The student has to sketch the electronic circuits and show the (i/p - o/p) curves].4) What's the difference between multimeter and clamp on meter?5) For the Figure below, calculate the Average value Vavg of the plot.

Since you have posted multiple question , we will solve first question for you . If you want any…

Q.3 Answer only Four of the following 1) If The AC Maxwell Inductance Capacitance Bridge has the following constants: R var = 5 kN, C, = 0.2 µF, R2 = 2.5 kn, and R3 var = 2 kN at frequency 1 kHz. Determine the unknown resistance, inductance and Q-factor of the bridge circuit. Drow tho blook diogrom of o ould

Q.3 Answer only Four of the following 1) If The AC Maxwell Inductance Capacitance Bridge has the following constants: R var = 5 kN, C, = 0.2 µF, R2 = 2.5 kn, and R3 var = 2 kN at frequency 1 kHz. Determine the unknown resistance, inductance and Q-factor of the bridge circuit. Drow tho blook diogrom of o ould

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume that dry soil has σ = 10−4 S/m, ε = 3εo, and μ = μo. Determine the frequency at which the ratio of the magnitudes of the conduction current density and the displacement current density is unity.
In a plate capacitor experiment, the percentage of error in magnitude of electric field is 3%.Then, what is the experimental value, which is lower than the theoretical value, of magnitudeof electric field, if the distance and potential difference between the plates are 10cm & 25V?
Find the relative permittivity of the dielectric material present in a parallel-platecapacitor if: (a) S = 0.12 m/, d = 80 μm, V = 12 volt, and the capacitor contains1 ?? of energy; (b)The stored energy density is 100 ?/?/, V = 200 volt, and ? =45 ??; (c) ? = 200 ??/? and ?# = 20 ??/?/.
When an ac potential of 1000 V is applied at a frequency of 1 MHz, a parallel-plate capacitor with dimensions of 38 mm by 65 mm and a plate spacing of 1.3 mm must have a minimum capacitance of 70 pF. Which of the materials listed in Table 2 might be a good fit? Why?
A capacitor is made from two flat parallel plates placed 2 mm apart, .and its capacitance at vacuum is 10-12- F , if 200 volt applied in between then a Dielectric material was entered and its Dielectric constant Is 49 , Calculate : a) the new value of capacitance after the entrance of the Dielectric b) what is the value of charge on Dielectric material surface c) the polarization p of the Dielectric material d) calculate the displacement and the field inside the Dielectric
3.(Part I) A 50 V voltage generator at 20 MHz is connected to the plates of an air dielectric parallel-plate capacitor with a plate area of 2.8 cm^2 and a separation distance of 0.2 mm. Find the maximum value of displacement current density and displacement current. (Part II) A dielectric material with permeability that of free space, permittivity = 9xpermittivity of free space, conductivity = 4 S/m, is placed between the plates of a parallel-plate capacitor. Calculate the frequency at which the conduction and displacement currents are equal.
A parallel-plate capacitor using a dielectric material having an Pr of 2.2 has a plate spacing of 2 mm (0.08 in.). If another material having a dielectric constant of 3.7 is used and the capacitance is to be unchanged, what must the new spacing be between the plates?
The relative dielectric coefficient of the planar electrode system given in the figure is Er = Er0 n. It changes linearly according to the x relation. Ero == 8,3 for this electrode system; n = 1.7 cm and the gap between the electrodes is given as a = 3 cm. 28 kV direct voltage is applied to this planar electrode system, so find the amplitude of the electric field strength at the point A (2.5cm, 3cm). (Edge effects will be neglected, electrode length b <15 cm)
Two concentric cylindrical plates have an outer radius of 4 cm, an inner radius of 3.8 cm, and a cylinder length of 10 cm. The gap of both plates contains air. Specify: a. Capacitance of capacitors (in pF, pico-farad). b. Capacitor charge (in nC, nano-coulomb) if the capacitor is connected to a 12 volt power source. c. Capacitance and charge captor if the gap of both plates is filled by the material with a dielectric constant of 2.3.
A ceramic capacitor has an effective plate area of 4 cm2 separated by 0.1 mm of ceramic of relative permittivity 100. Calculate the capacitance of the capacitor in picofarads. If the capacitor in part is given a charge of 1.2 µC what will be the p.d. between the plates?
Calculate the gravimetric capacitance of a carbon based electrode with an aqueous electrolyte solution. Assume the surface area of the carbon electrode is 1200 m2/g, and the relative static permittivity of the aqueous electrolyte solution is 80. The permittivity of free space is 8.85 × 10−12 F/m. Indicate any other assumptions you have to make.
A parallel plate capacitor has an area of 7.45 × 10−4?2and its plates are separated by a distance of 2.45 ?? across which a potential of 20 ? is applied. If a material with dielectric constant 6 is introduced between the plates, determine the capacitance, the charge stored on each plate, the dielectric displacement and the polarization.