Q.3: If 82C55 shown in Figure below is configured as follows: PA as input, PB as output, and PC as output and all ports in mode-0. a- Find the port address assigned to A, B, C, and control register. b- Find the control byte (word) for this configuration. c- Write a program to input the data from PA and find X & Y, then sent the result of X to port B and the result of Y to port C. X = A -5, Y = A + 2 DO DO D7 07 Write signal. Read signal WR RD B CL A0 A1 A7 A1 CU A15 CS tt 82CSSA

Q.3: If 82C55 shown in Figure below is configured as follows: PA as input, PB as output, and PC as output and all ports in mode-0. a- Find the port address assigned to A, B, C, and control register. b- Find the control byte (word) for this configuration. c- Write a program to input the data from PA and find X & Y, then sent the result of X to port B and the result of Y to port C. X = A -5, Y = A + 2 DO DO D7 07 Write signal. Read signal WR RD B CL A0 A1 A7 A1 CU A15 CS tt 82CSSA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An A/D converter uses 14-bit numbers and has a voltage range between +6V to -6V. ( Use 2 decimal places) a) What is the dynamic ratio of the system in dB? b) Find resolution of digitalization in μV that is expressed as the smallest voltage increment?
Develop the truth table and constellation diagram of QPSK using I -channel reference cos wct and 90 degrees phase shift for IQ inputs 00 and 10. Draw the analog output waveform of the given inputs
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Q1.A) If an 8-bit SAR ADC is used to digitize 8V full scale signal, what will be the digital o/p for an analog i/p of 5.76 V (perform complete analysis)?
If VBE = 0.7 and B = 100 Calculate the value of: 1. IE ? 2. Av ? 3. if R1 is open cct then the value of Av? 4. if the capasitor C2 is removed then the Ri seen by AC signal is? 6. the AC resistance of emmitter re is ?
Course: Data Networks - ECTE201 Write three types of analog-to-analog modulation and illustrate one of the modulations. Kindly provide a brief anwer for this question
Determine Av=Vo/Vi. If the two-port parameters for the fixed-bias configuration are Zi =1.071 KΩ, Zo=3 KΩ, and AvNL= -280.11.
During the turn-on and turn-off of a power transistor,the current-time and voltage-time relationshipsare as shown in the adjacent figure. Observe thewaveforms and calculate,1. The OFF-state power dissipation (static);2. The switch ON-state power dissipation(static);3. The average switching loss for the OFFtransition (dynamic);4. The average switching loss for the ONtransition (dynamic);Assume a switching frequency of 1kHz with Vx = 422V
Using 741 op amp, design a suitable circuit to generate Binary Phase Shift Keyiing(BFSK) modulator. Design should perform in such a way that the BFSK output should contain a frequency of f1=2kHz when message signal is low and f2 =4kHz when the message signal is high. Take the frequency of message signal as 200Hz. Draw the clear circuit diagram and calculate the values of resistors and capacitors used.
Using Flash ADC method to convert the analoge voltage signal to digital (3-bit) ,where Vi=5V and Vref=7V
which of the following devices dose not belong to the transiator family? a-BJT b-IGBT c-GTO d-MOSFET
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?