Q1 (a) Based on electrical DC circuit as depicted in Figure Q1(a), (i) Determine the mesh currents I, I, I; and I, by using mesh analysis. Then calculate the branch current, I (ii) Calculate the power at 50 V voltage source and determine whether the power is supplied or absorbed by the voltage source. 4Ω 20V 50V 10V I3 I4 D4A 50 Ω 20 Ω Figure Q1(a)

Q1 (a) Based on electrical DC circuit as depicted in Figure Q1(a), (i) Determine the mesh currents I, I, I; and I, by using mesh analysis. Then calculate the branch current, I (ii) Calculate the power at 50 V voltage source and determine whether the power is supplied or absorbed by the voltage source. 4Ω 20V 50V 10V I3 I4 D4A 50 Ω 20 Ω Figure Q1(a)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve this question1)In concentrating solar power - central receiver, one of the following advantages is wrong comparing to parabolic troughSelect one:a. it requires less gross land area and less capital costb. None of thesec. No need for miles of tubes absorber tubes circulating HTFd. Less water usee. Achieves higher temperature and pressure2) The temperatures necessary to get sufficient efficiency to convert the earth’s heat to electrical power is:Select one:a. 160 °Cb. 230 °Cc. 130 °Cd. None of thesee. 200 °C
As shown in the Figure , an external load resistor, R, is connected across the terminal a-b of the DC circuit. Based on Norton’s Theorem, calculate and analyse the circuit shown in the figure ( given V1=60V, V2=20V, R1 = 22ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm,) find R if i =0.5. What is the practical range of current i and value of R?. Kindly modify the circuit by changing only one of the parameters (either voltage or resistor value) so that i = 0.3 A.
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A substation supplies power by four feeders to its consumers. Feeder No. 1 supplies six consumers whose individual daily maximum demands are 70 kW, 90 kW, 20 kW, 50 kW, 10 kW, and 20 kW, while the maximum demand on the feeder is 200 kW. Feeder No. 2 supplies four consumers, whose daily max. demands are 60 kW, 40 kW, 70 kW, and 30 KW, while the maximum demand on feeder No. 2 is 160 kW. Feeders Nos. 3 and 4 have a daily maximum demand of 150 kW and 200 kW respectively, while the maximum demand on the station is 600 kW. Determine the diversity factor for the four feeders. 1.18 1.25 1.30 1.36
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Flux Luman output per 200 W lamp Luman output per 500 W lamp Number of 500W lamps required Number of 220W lamps required Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
As shown in the Figure , an external load resistor, R, is connected across the terminal a-b of the DC circuit. Based on Norton’s Theorem, calculate and analyse the circuit shown in the figure ( given V1=60V, V2=20V, R1 = 22ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm,) to determine the current, i, when R = 200 Ω
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:It is required to provide illumination of 150 meter-candle in a factory hall 45m x 15m. Assume that the depreciation factor is 0.80, the coefficient of utilization is 0.40 and the efficiency of the lamp is 20 lumens per watt. Calculate the number of 250-W lamps. 63 62 61 60
Given that Vs is 75 V, R1 is 9 Ohm, R2 is 3 Ohm, R3 is 8 Ohm and R4 is 20 Ohm. Find equivalent VTh with respect to terminals a, b in the circuit shown. (Unit: V) Find equivalent RTh with respect to terminals a, b in the circuit shown. (Unit: Ohm)
Determine I1, I2, and I3. Using A. Branch-current analysis B. Mesh Analysis C. Nodal Analysis Compare the result obtained applying the three methods of analysis. Which method is the easiest and most convenient to use?
Q18) A substation of 440kV, 5000A located at Al-Qabil, is feeding the whole of the Al-Alaya loads (houses). This substation has the setup of PT, CT and a small voltmeter of range (0-600V) connected for measurement purposes. Then, the actual Voltage (V1) in the line when voltmeter reads a Voltage of 250V is calculated as,. a. 275kV b. 375kV c. 270kV d. 272kV
Solve by applying Millman's theorem, apply D.V.V and D.V.C where they can be applied a) Find: I1, I2, ..., I10 = ?; V1, V2, ..., V10 = ?; P1, P2, ..., P10 = ? b) Calculate power balance c) Do KVL on meshes and KCL on main nodes
Kindly give neat and clean exlanation Calculate the power dissipated by the voltmeter and by resistor R given figure when (a) R = 250 ohm and (b) R = 2 Mohm. Assume that the voltmeter sensitivity (sometimes called the figure of merit) is 10 Kohm/V.