Q1/ A volume of the vessel A is 0.5 m' contains saturated water at 275 °C, 80% quality. The pressure of cylinder B will be floated at 300 kPa, cylinder B in the beginning is empty. The air is flowed into cylinder B when the valve is opened and reaches to equilibrium state of 300 kPa, 275 °C. Determine the heat transfer during the process.

Q1/ A volume of the vessel A is 0.5 m' contains saturated water at 275 °C, 80% quality. The pressure of cylinder B will be floated at 300 kPa, cylinder B in the beginning is empty. The air is flowed into cylinder B when the valve is opened and reaches to equilibrium state of 300 kPa, 275 °C. Determine the heat transfer during the process.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter46: Room Air Conditioners

Section: Chapter Questions

Problem 15RQ

See similar textbooks

Similar questions

Water at 0.1MPawith a quality of 25% has its temperature raised 40.37 0C in a constant pressure process. What is the new quality and enthalpy of water? Draw a schematic diagram,andthen plot the state/s and process, whichever is applicable in a t-sdiagram
Saturated steam vapor at 250°C moves along its isotherm until the pressure becomes 1MPa. Locate the end state points on the Mollier chart and for each kilogram of steam processed determine (a) the initial pressure, (b) the change of enthalpy, (c) the change of entropy.
For the compressed liquid, what property(ies) is (are) used to determine other properties (1) if the compressed liquid table is used?___________ A. Pressure only B. Temperature only C. Pressure and Temperature D. either pressure or temperature
Saturated water vapor at 50°C has its pressure decreased to increase the volume by54.571% keeping the temperature constant. To what pressure should it be expanded? Draw a schematic diagram,and then plot the state/s and process, whichever is applicable in a t-sdiagram
2. Saturated steam at 100°C is heated to 350°C at constant pressure. Use the steam tables to determine: a. The pressure in bar. b. the required heat input (J/s) if a continuous stream flowing at 100 kg/s undergoes the process.
A furnace heats water at a saturated state with a pressure of 1 bar. How much heat is given When the water condition in the tank is 15 bar and 500°C. Specify: a) Heat needed? b) Internal changes in energy? c) Work done?
Q3: A two phase of saturated water and saturated vapour at a temperature 240 °C where a container having a total volume a 0.8 m'. If the mass of a liquid is (5) kg. Evaluate the following: (1) The saturated pressure, (2) The volume in each phase, (3) The total mass in container, (4) The specific enthalpy, the specific entropy, and The specific internal energy and the specific volume.
An insulated cylinder-plunger device with a constant load contains 2 L of saturated liquid water at a temperature of 80 °C . A paddle wheel agitates the water, contributing 500 kJ to the system, while for 10 min a current of 8 A passes through a 110 V resistor placed in the water. It is correct to state: I) Information is missing to calculate the moving boundary work. II) The final state is a vapor-liquid mixture at 47.42 kPa. III) In the final state, the volume is equal to 0.781 m3/kg IV) The sum between the electric work and the work of the paddlewheel is equal to hfg
Saturated steam at 3.27MPa undergoes a T=c process until it becomes 0.8MPa. Calculate dH, dS, Wsf, Wnf, and Q. (m=2kg/min)
The pressure of the air in a starting vessel is 40 bar and the temperature is 24°C. If a fire in the vicinity causes the temperature to rise to 65 °C. Neglect anyincrease in the volume of the vessel which is 5 liters. determine the following: a. The thermodynamic process the problem representsb. the pressure, temperature, and volume after the processc. change in internal energy, change in enthalpy and change in entropy
Mr Zul operates a hot plate. He places a closed, rigid container of volume 0.5 m3on the hot plate. Initially, the container holds a saturated mixture with quality ofvapour of 0.5, at a pressure of 100 kPa. After heating, the pressure in the containerincreases to 150 kPa.a) Calculate the mass of vapour at the initial and final states (in kg).b) If heating is allowed to continue, find the pressure (in kPa) when thecontainer holds only saturated vapour.c) Sketch the T – v diagram for this system.
Water at P1 = 200 kPa with a quality of 25% has its temperature raised 20 oC (T2 = T1+20 0C) in a constant pressure process. What is the initial (v1) and final (v2) specific volumes?