Q1/ complete the dimensional formula and Sl units for table. US SI. No Physical Quantity S.I Unit Dimensional Formula customary unit 1 Area (A) work (w) Density (d) 4 Speed (s) stress (6) Acceleration (a) Q2/ Suppose we are told that the acceleration a of a particle moving with uniform speed v in a circle of radius r is proportional to some power of r, say r", and some power of v. say v also some power of mass, say m°. Determine the values of n 23

Q1/ complete the dimensional formula and Sl units for table. US SI. No Physical Quantity S.I Unit Dimensional Formula customary unit 1 Area (A) work (w) Density (d) 4 Speed (s) stress (6) Acceleration (a) Q2/ Suppose we are told that the acceleration a of a particle moving with uniform speed v in a circle of radius r is proportional to some power of r, say r", and some power of v. say v also some power of mass, say m°. Determine the values of n 23

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

The only possible dimensionless group that combines velocityV , body size L , fl uid density ρ , and surface tensioncoeffi cient σ is( a ) L ρσ / V , ( b ) ρ VL 2 / σ , ( c ) ρσ V 2 / L , ( d ) σ LV 2 / ρ ,( e ) ρ LV 2 / σ
Figure shows the flow of water over a dam. Thevolume fl ow Q is known to depend only on crest width B ,acceleration of gravity g , and upstream water height Habove the dam crest. It is further known that Q is proportionalto B . What is the form of the only possible dimensionallyhomogeneous relation for this flow rate?
Aeronautical engineers measure the pitching moment M0of a wing and then write it in the following form for use inother cases:M0 =βV2 AC ρ where V is the wing velocity, A the wing area, C the wingchord length, and ρ the air density. What are the dimensionsof the coeffi cient β ?
Books on porous media and atomization claim that the viscosityμ and surface tension Y of a fl uid can be combinedwith a characteristic velocity U to form an important dimensionlessparameter. ( a ) Verify that this is so. ( b ) Evaluatethis parameter for water at 20°C and a velocity of3.5 cm/s. Note: You get extra credit if you know the nameof this parameter.
The height H that fluid rises in a liquid barometer tubedepends upon the liquid density ρ , the barometric pressurep , and the acceleration of gravity g . (a) Arrange these fourvariables into a single dimensionless group. (b) Can youdeduce (or guess) the numerical value of your group?
When fluid in a pipe is accelerated linearly from rest, itbegins as laminar flow and then undergoes transition toturbulence at a time t tr that depends on the pipe diameterD , fluid acceleration a , density ρ , and viscosity μ .Arrange this into a dimensionless relation between t trand D .
During World War II, Sir Geoffrey Taylor, a British fl uiddynamicist, used dimensional analysis to estimate theenergy released by an atomic bomb explosion. He assumedthat the energy released E , was a function of blast waveradius R , air density ρ, and time t . Arrange these variablesinto a single dimensionless group, which we may term theblast wave number .
The belt in Fig. P1.52 moves at a steady velocity V andskims the top of a tank of oil of viscosity μ , as shown.Assuming a linear velocity profi le in the oil, develop asimple formula for the required belt-drive power P as afunction of ( h , L , V , b , μ ). What belt-drive power P , inwatts, is required if the belt moves at 2.5 m/s over SAE30W oil at 20° C, with L = 2 m, b= 60 cm, and h = 3 cm?
For most gases at standard or near standard conditions, the relationshipamong pressure, density, and temperature is given by the perfect gasequation of state: p = ρRT, where R is the specific gas constant. For airat near standard conditions, R = 287 J/(kg · K) in the International System of Units and R = 1716 ft · lb/(slug · ◦R) in the English Engineering System of Units. Using the above information, consider the following two cases: a. At a given point on the wing of a Boeing 727, the pressure andtemperature of the air are 1.9 × 104 N/m2 and 203 K, respectively.Calculate the density at this point.b. At a point in the test section of a supersonic wind tunnel, the pressureand density of the air are 1058 lb/ft2 and 1.23 × 10−3 slug/ft3,respectively. Calculate the temperature at this point.
Let the velocity, u (m/s), specific heat, cp (kJ/(kg K)), and temperature, T (K), be used to define a dimensionless number given by u2cpaTb. The powers must be a=[Blank-1] and b=[Blank-2].
The Stokes-Oseen formula for drag force on a sphere at low speed is given asD = 3dV +916V 2d2, where D is drag, V is velocity, is density, d is the sphere diameter, and is the viscosity coe¢ cient.(a) Using the formula given, Önd the dimensions of the viscosity coe¢ cient. (Donít simply look upthe dimensions; use the formula to show them.) Be sure to show your work. Find the primaryunits of viscosity in SI and British units.(b) Verify that the Stokes-Oseen formula is dimensionally homogeneous.
Q3: Analyze the primary dimensions of the universal ideal gas constant Rµ using the ideal gas law, Pv = nR, T where P is pressure, v is volume, T is absolute temperature, and n is the number of moles of the gas.