L-shaped part is to be bent in a V-bending operation on a press brake from a flat blank 4.0 in by 1.5 in that is 5/32 in thick. The bend of 90° is to be made in the middle of the 4-in length. (a) Determine the dimensions of the two equal sides that will result after the bend, if the bend radius = 3/16 in. For convenience, these sides should be measured to the beginning of the bend radius. (b) Also, determine the length of the part's neutral axis after the bend?

L-shaped part is to be bent in a V-bending operation on a press brake from a flat blank 4.0 in by 1.5 in that is 5/32 in thick. The bend of 90° is to be made in the middle of the 4-in length. (a) Determine the dimensions of the two equal sides that will result after the bend, if the bend radius = 3/16 in. For convenience, these sides should be measured to the beginning of the bend radius. (b) Also, determine the length of the part's neutral axis after the bend?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a full draw, an archer applies a pull of 130 Nto the bowstring of the bow shown in the figure. Determinethe bending moment at the midpoint of the bow.
What is the shear force (in kips rounded to the nearest whole number) at x = 6.0 ft?- What is the bending moment (in kip-ft rounded to the nearest whole number) at x = 6.0 ft? What is the shear force (in kips rounded to the nearest whole number) at x = 9.0 ft? What is the bending moment (in kip-ft rounded to the nearest whole number) at x = 9.0 ft? What is the maximum bending moment? Express your answer in kip-ft rounded to three significant figures.
Derive the formula for the maximum shearing stress due to bending if the the cross section is a criclewith radius r and shear force V.
The energy required to shear a 1-in. round bar is approximately 1000 ft-lb. In use, the shearing machine is expected to make a maximum of 40 cutting strokes a minute. The frictional losses should not exceed 18 % of the motor output. The shaft carrying the flywheel is to average 150 rpm. (a) What motor horsepower is required? (b) Assuming a size of flywheel and choosing appropriate f C, find the mass and sectional dimensions of the rim of a cast-iron flywheel. The width of the rim is to equal the depth and is not to exceed 3 ½ in. It would be safe to assume that all the work of shearing is supplied by the kinetic energy given up by the flywheel.
A 2 mm thick metal sheet is to be bent at an angle of one radian with a bend radius of 100 mm. If the stretch factor is 0.5, Determine the bend allowance.
Answer only in 10minutes Find the maximum bending moment and maximum shearing force
Fig 1 and 2 pictured with part A calculate the magnitude of the shear stress at the point due to internal shear on the section. calculate the combined normal stress at the point due to internal normal force and the internal bending moment of the section. Answer should be stress
Fig. 2, shows a cylindrical rod of 25 mm diameter, welded to a flat plate. The cylindrical fillet weld is loaded eccentrically, by a force of 20 kN acting at 200 mm from the welded end. If the size of the weld is 20 mm, determine the shear stress and bending moment.
For the given fig find the correct representation of the longitudinal variation of the bending stress
The cross-sectional area of a wide-flange I-beam has the dimensions shown. Obtain a close approximation to the handbook value of Ix¯ = 654 in.4 by treating the section as being composed of three rectangles.
derive shear and moment equations
Need correct solution. If C is the mid-point of PQ; What is the magnitude of bending moment at fixed end O?