Q1: Find the Diameter of the shaft macleof A cold-drawn steel. Assume hatultimate stress is 370 MPa and the factorof the safety is 3. For pulley A consider 250 Dia.the loose belt tension is 15 percent of thetension on the tight side.*All dimensions units are in mm.300TzA400T₂50 N.270 N.45°150.300 Dia. TP x 602 KNT = (T₁ - T₂) RcTwMz16+T²xxx d³

Given: The ultimate stress = 370 MPa The factor of safety, n = 3 The tension in the loose side, T2 =…

Q1: Find the Diameter of the shaft made of A cold-drawn steel. Assume that ultimate stress is 370 MPa and the facter of the safety is 3. For pulley A consider the loose belt tension is 15 percent of the tension on the tight side. * All dimensions units are in mm. 300 250 Dia. T₂ 400 T₁ 50 N. 270 N. 150 300 Dia. T Px 60 2 RN T = (T₁-T₂) Rc √√M² + T² = cxd³ C T- 16

Q1: Find the Diameter of the shaft made of A cold-drawn steel. Assume that ultimate stress is 370 MPa and the facter of the safety is 3. For pulley A consider the loose belt tension is 15 percent of the tension on the tight side. * All dimensions units are in mm. 300 250 Dia. T₂ 400 T₁ 50 N. 270 N. 150 300 Dia. T Px 60 2 RN T = (T₁-T₂) Rc √√M² + T² = cxd³ C T- 16

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and a torque of 1 kN.m. The member is made of steel the Ultimate Tensile Strength 440 MPa, Yield Tensile Strength 370 MPa. With a safety factor of 4, kt = km = 1.5 and keyway stress consternation is presented. According to the maximum shear stress theory, the shaft diameter will be: a. 160 mm b. 74 mm C. 145 mm d. 92.5 mm e. 60 mm f. 66 mm
Draw FBD and determine Stress and Safety Factor of Bicycle Axle (Thru Axel) Specification Weight of cyclist = 120 kg. Materials: Aluminum alloy (AL 6061-T6) Dimension: Length = 122 mm, Diameter = 12 mm, Thread pitch = 1.75 mm, Thread Length = 16 mm.
Q1. A tensile testing machine operates using two lead screws. Both lead screws have a square thread profile and can withstand the maximum load of 16 tonnes & torque of 150 KNm. The pitch width p = l = 4 mm. what is the efficiency of the square thread?
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100 mm from its support and has horizontal belts, tension ratio being 2.5. If the shear stress is to be limited to 80MPa while transmitting 45 kW at 900 rpm. Find the shaft if it is to be used for the input - output belts being on the same or opposite sides.
In the Bolted Connection shown, find the following by ASD.Specifications:M20 Bolts in standard holes. Nominal hole diameter = 22mmEffective Hole diameter = nominal hole diameter + 2 mmA325 steel boltAssume thread in shear planeFv = 372 MPaProperties of Angle Bar< 125 x 125 x 13 mmA = 3065 mm²x = 36.3 mmy = 36.3 mmFy = 248 MPa , Fu = 410 MPa 1. For angle bars used as bolted tension element connected to another element only on one leg, the effective area Ae = UAn. Where: An = Net area, U = Shear lag factor = 1 – x/L, L= center to center longitudinal distance of extremely located fasteners, X= distance from centroid of angle bar to surface of contact of joined elements. What is the shear lag factor of our angular bar? a. 0.454 b. 0.9 c. 0.838 d. 0.869 2. Considering RUPTURE of angle bar, what is the allowable force P that the connection can handle if allowable RUPTURE stress in net area of angle bar is Fu/2 a. 463.83 kN…
(1) A single square thread power screw is to raise a load of 70kN. The screw has a major diameter of 36mm & a pitch of 6mm. The coefficient of friction of the thread & the collar are 0.13 & 0.1, respectively. If the collar mean diameter is 90mm & the screw turns 60rpm, find: (a) power input of the screw; (b) combined efficiency of the screw & collar.
3) A flange coupling is to connect two 60mm shafts. The hubs of the coupling are 120mm, 100mm thick, & the flange webs are 20 mm thick. Six M16 bolts fasten the flange from a 165 bolt circle. The keyway is 15mm shorter than the hub’s thickness & the key is 15mm x 15mm. The coupling transmits 45kW @ 450rpm. The yield point in shear for all materials is half of its yield point in tension or compression. Yield tensile strength is 0.75 of ultimate strength of the materials. The Sult is 448N/mm2 . Find: (a) the shear stress in key; (b) the bearing stress in key; (c) the shear stress in bolts; (d) bearing stress in flange.
M16 (h=2mm, d1=13.54mm, d2=14.7mm) material quality 8.8 bolt-nut connection Blowout= 2500 daN prestressbored with. Factor of safety S=2.5, key length L=10.d, coefficient of friction µo='=0.17; Average of contact surface with nutdiameter is given as d0=1.4.d. According to the given;a) strength control calculation during tightening;b) hand force that must be applied to the wrenchc) When the pre-tensioning force is applied, the elongation of the part is given as lp= 0.015mm, and the elongation of the bolt as lc= 0.030mm. BusinessSince the total elongation of the bolt is lctop=0.040mm for Ftop=3000 daN after the force is applied, we can define the characteristic of the bolt.find it.d) the characteristic of the part and the minimum remaining shortening value önlp after the prestressing forcee) Calculate the portion of the operating force on the bolt (Fic) and the part (Fip).f) Calculate the pre-tension force Fön' value remaining in the connection after the operating force has been…
Please full answer A) Explain 1) Different types of Keys 2) Interference fit 3) Couplings. B) A simply supported shaft is shown in the following Figure. A constant magnitude distributed unit load p is applied as the shaft rotates. The shaft is also subject to a steady torque of Tmax = 2000 N-m., find the diameter of shaft required to obtain a safety factor of 2.5 in fatigue loading if the shaft is steel of Sut = 814 MPa and Sy = 703 MPa. The dimensions are in cm, the distributed force in N/cm, and the torque is in N-m. No stress concentrations are present, the shaft is machined, the required reliability is 90%, and the shaft operates at room temperature.