Q1: for the circuit as following in fig.4 when Vin=30V and Fin=50HZ: 1. Calculate the values of Impedance (Z1, Z2, Zz and Z4). 2. Calculate the values of Impedance total (Zt). 3. Calculate the values of current (I1, I2, I=I4). 4. Calculate the values of voltage (V2 and V3+V4).

Q1: for the circuit as following in fig.4 when Vin=30V and Fin=50HZ: 1. Calculate the values of Impedance (Z1, Z2, Zz and Z4). 2. Calculate the values of Impedance total (Zt). 3. Calculate the values of current (I1, I2, I=I4). 4. Calculate the values of voltage (V2 and V3+V4).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17MCQ: Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A....

See similar textbooks

Related questions

Q: k QFor the network shown in figure,determine the input impedance, output impedance,voltage…

A: Given hie=1.6k ohm,hre=2*10-4 , hfe=110 ,hoe=20us. Rc=2.2 k ohm , RL=1.1k ohm, R1=50k ohm R2=50k…

Q: Calculate the average and the root-mean-square value of the output voltage for the network in the…

A: Given circuit is full wave rectifier , we know formula for average value and RMS value for full wave…

Q: The source current in the circuit shown is 3 cos 5000t A. a) What impedance should be connected…

A: For the given circuit with the current is 3cos5000t Following is determined as shown below

Q: A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance…

Q: O Uoy the network. Then, determine the power factor (pf) of the network. Based on the calculated…

Q: 12.25 In the circuit of Fig. 12.54, if Vab = 220/10°, Vôc = 220/–110°, Vca = 220/130° V, ìnd the…

Q: 3. Consider the circuit of Figure 2: Is Ri BOVLŐ ( Fig.2 (a) Find ZT. (b) Determine the currents I1,…

Q: A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance…

A: A coil (5 + j8) ohms with in series with a capacitive reactance Xc, this series combination is then…

Q: Ql) For the network of Fig. A: a. Determine re. (hint: approximate analysis) b. Find Avymid = Vo/Vi.…

Q: For the circuit shown in Fig. below, calculate Avf, Zif and Zof. Where he= 50 and hie 1.1 k2. 15 V…

A: Given circuit: hfe=50hie=1.1 kΩ To find: Avf, Zif, Zof?

Q: Q) For the circuit of Fig. 1: a. Find the total impedance Zy in polar form. h. Draw the impedance…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Find the Thevenin's equivalent as seen from terminals a- b for the circuit given in Fig. 1.…

A: In this question, We need to determine the Thevenin equivalent circuit across the terminal a and b.…

Q: Find the Thevenin's equivalent as seen from terminals a- b for the circuit given in Fig. 1.…

A: In this question, We need to determine the maximum average power transfer to the terminal a and b.…

Q: R1 Ib=5 Ic R2 + Zyük C V

Q: | Zc For the circuit given above, the circuit parameters are; Is = 3 A, ZR = 10 ohms, Zc = -j6 ohms,…

A: The value of inductance and capacitance is given in ohm that means they are in impedance form and…

Q: Q3: For the circuit shown in fig.(1), 3-phase voltage with positive sequence, if the supply voltage…

A: In this question, we need to find the value of resistance R. Reading of the Wattmeter W1 and W2.…

Q: E8.21 Find V, in Fig. ES.21 using mesh analysis. 24/0 V j4n j20 60 4 2 VA V,-j20 2 VA Figure E8.21

A: given here a circuit and asked to find the value of Vo in the circuit.

Q: The voltage u=Acos(314t – B) Volts is applied to two impedances connected in series. Your first…

Q: 1 4/0° V -j4 2 6Ω 8 Ω j5 Ω el 10/0° V 3/0° 14 13

Q: The circuit given in the figure below is continuously sinusoidal and the element values in the…

Q: E Ę Referring to Fig. 12.87, we have, and Subtracting 10,000 210-5774 210 volts (5686+/1003) volts…

A: Given here a data and asked to explain one equation.

Q: 802 802 Q.22: For the following electric circuit, find Z and Y parameters? Also, compute input and…

A: Given data:

Q: Q2:- Final the therenin equivalent Circuit For the ne twork Shown in fig. 22 12v 42

Q: Question 03: For the network of Fig. 2: a) Find the total impedance ZT. b) Find the voltage V₁ in…

A: In this question we need to find the voltage V2 and source voltage in phasor form .

Q: Find the Thevenin equivalent of the 2-terminal a – b in sinusoidal steady state. (Fig.1) e(t)=2…

Q: A set of 100-ohm resistor, 0.5-Henry inductor, and 50-microFarad capacitor elements are arranged in…

Q: a) Find the Thevenin equivalent of the 2-terminal a – b in sinusoidal steady state. (Fig.1)…

A: Ans (a) In case of capacitance -: Xc = 1wc = 12×1 = -j0.5 In case of inductance -: XL = wL = 2×1 =…

Q: Assuming an operating frequency of 40 rad/s for the circuit shown, the load impedance is 50 <-45° Q,…

A: Find the average power across the 1k ohm resistance. Average power not depend on the time. P= I2…

Q: Question 1 Using Nodal Analysis, what is the value of Vg if the reference node is at node f if Z₁ =…

Q: A 300 m ring distributor has loads as shown in Fig. 13.45 where distances are in metres. The resis-…

Q: Ri Ib-5 Ic R2 L + Zyūk e(t) V 'Ic

Q: Please show your solution step by step. For the given question take y =5 In the given AC circuit,…

Q: Q1/ For the circuit shown below, determine the value of Vo, using Nodal analysis. 32 62 ww 12 V 26…

Q: b. Find the total impedance of the network, Zr seen by the voltage source. Figure Q3 shows the…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Apply the knowledge gained from the ac analysis of BJT to construct the AC equivalent model of the…

Q: 2) For each of the following circuit diagrams, plot the graph for total impedance versus frequency,…

A: To solve the above problem, one should have a basic idea about the working of AC circuits. The…

Q: 1. A series-connected circuit has R= 4 Q and L = 25 mH. (a) Calculate the value of C that will…

Q: I total 11 12 13 Al 5 Ohm 3 Ohm 10 V/50 Hz/0 Deg 8 Ohm t0.0382 H 0.00079 F Report : Q1: for the…

Q: a) Electricity Company of Ghana (ECG) has awarded a contract to Accra Institute of Technology (AIT)…

A: (1): The given three phase current distribution network is a delta connected system in which the one…

Q: Determine the phasor currents I1 and I2 in the circuit of Fig. 13.13. 50 j2 2 J3 Ω 20/60° V j6 2…

A: Mutual Induction: Whenever flux in one coil links with the second coil, an EMF is induced in the…

Q: A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad.…

Q: Q3: Consider the Y-A three-phase circuit in Fig. 1 with: Three-phase circuits Van = 50 cos(100t +…

Q: Q4) For the network in Fig.5. a. Find the total impedance ZT and the admittance YT. b. Find the…

Q: a) Find the Thevenin equivalent of the 2-terminal a – b in sinusoidal steady state. (Fig.1) e(t)=2…

Q: I total 11 Ohm 3 Ohm 10 v50 Hz/0 Deg Ohm Eo.0382 H 0.00079 F Report : Ql: for the circuit as…

A: Concept of Parallel Circuit: In Parallel Connection the positive terminal of all the elements are…

Q: 13 2 µF 2. Consider the network of Fig. P2.1. The angular frequency w= 1000 rad/s. (a) Label all…

A: In this question we need to calculate the unknown voltage V1,V2 and V3 and unknown currents I1, I2,…

Q: H.W. (2): For the circuit of Fig. 37. a. Find the total impedance Z, in polar form. b. Draw the…

Q: A coil of wire having a value of (6 + j9) ohms is connected in series with a capacitive reactance…

Q: A 300 m ring distributor has loads as shown in Fig. 13.45 where distances are in metres. The resis-…

A: Only first question is to be answered, kindly repost the remaining questions.

Q: 1. What is the phase relationship between VR and VC components in a series AC circuit? 2. Based on…

Concept explainers

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.

Question

100%

Q1: for the circuit as following in fig.4 when Vin=30V and Fin=50HZ:
1. Calculate the values of Impedance (Z1, Z2, Z3 and Z4).
2. Calculate the values of Impedance total (Zt).
3. Calculate the values of current (I1, I2, I3=I4).
4. Calculate the values of voltage (V2 and V3+V4).

6.136 uF
se0 Ohm
390 Ohm
0.859 H
220 Ohm
Z4
30 VISO Hzo Deg
330 Ohm
14.475 uF
1.49 H
Fig. 4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find out i) Input impedance function and ii) V0(s)/Vin(s) for the network shown in the Fig please write correct answers else I will downvote
A coil of wire having a value of (5 + j8) ohms is connected in series with acapacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 4 /0 o ohms, calculate the values of Xc and R.
1. Perform the following steps for the given circuit in below.a) Find the Av, if the IDSS = 8mA, VP = -5V, VDD = +24V, RD = 4.3kΩ, RG =1.2MΩ, RS1 = 120Ω and RS2 = 470Ωb) Find the Av and Vout, if the IDSS = 6mA, VP = -6V, VDD = +24V, Vi = 80mV_rms,RD = 3.6kΩ, RG = 1.2MΩ, RS1 = 150Ω and RS2 = 470Ω
Solve the impedances of the circuit using mesh analysis. Complete the table given. Note: If there are no coefficients for a particular parameter, input zero. Round off only the final answer to five decimal places if possible. @mesh 1: Z11I1 + Z12I2 +Z13I3 + Z14I4 = Source1 @mesh 2: Z21I1 + Z22I2 + Z23I3 + Z24I4 = Source2 @mesh 3: Z31I1 + Z32I2 + Z33I3 + Z34I4 = Source3 @mesh 4: Z41I1 + Z42I2 + Z43I3 + Z44I4 = Source4
A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 4 /0o ohms, calculate the values of Xc and R.
For the circuit shown in the figure below, use the mesh current method to find: a) The mesh currents, IA and IB b) The output voltage V2, and draw its phasor diagram C) The input impedance, Zin, d) If w = 314.14 rad/s, specify the values of the passive elements of the input impedance
a) Electricity Company of Ghana (ECG) has awarded a contract to Accra Institute of Technology (AIT) to design a three-phase current distribution network for it. The three-phase current distribution network is given in Fig. 1 below: Figure1 AIT has constituted a project team to design the network of which you are a member i. How would you analysis the network with a diagram using your knowledge of network analysis? [1 Marks] ii. Use your method of analysis to derive formulas involving RX, RY and RZ [5 Marks] iii. Use the formulas in (ii) to find R1, R2 and R3 if RX=15 Ω, RY=10 Ω and RZ=35 [2 Marks]
Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A. If one says that an inductor absorbs zero real power and positive reactive power. is it (a) True (b) False B. If one says that a capacitor absorbs zero real power and negative reactive power (or delivers positive reactive power), is it (a) False (b) True C. If one says that a (positive-valued) resistor absorbs (positive) real power and zero reactive power, is it (a) True (b) False
The circuit given in the figure below is continuously sinusoidal and the element values in the circuit are e (t) = 2Cos (t + 90) volts, C = 1F, L = 2H, R1 = 1Ω, R2 = 2Ω.a) Find the Thevenin equivalent of the circuit in the form V = ZThI + VTh, viewed from the A-B ends looking left.b) Maximum active power is desired to be transferred to the Z load impedance connected to A-B terminals. What should be the Zyload impedance? Calculate the maximum active power transferred to the load for this impedance value.
The circuit given in the figure below is continuously sinusoidal and the element values in the circuit are e (t) = 2Cos (t + 90) volts, C = 1F, L = 2H, R1 = 1Ω, R2 = 2Ω.a) Find the Thevenin equivalent of the circuit in the form V = ZThI + VTh, viewed from the A-B ends looking left.b) Maximum active power is desired to be transferred to the Zload impedance connected to A-B terminals. What should be the Zload impedance? Calculate the maximum active power transferred to the load for this impedance value.
Eae = _______ V Vab = _______ VVbc = _______ V Vcd = _______ VVbf = _______ V Vcg = _______ V please compute using the given circuit, show complete solution
α=4 β=4For the adjacent circuit, Vab=(400+5β)V is given and the source part is balanced. Since it is known as ZAN=j2α Ω, ZBN= 3α Ω and ZCN=-j3α Ω, calculate the value of the current Ib by its angle, ignoring the impedances of the transmission lines.Can you please post your solutions, it's very important