A coil of wire having a value of (6 + j9) ohms is connected in series with a capacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 5 N Z0° . Calculate the values of Xc and R.

A coil of wire having a value of (6 + j9) ohms is connected in series with a capacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 5 N Z0° . Calculate the values of Xc and R.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17MCQ: Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A....

See similar textbooks

Related questions

Q: o18 V 4.7 k2 R1 Ic oVc = 12 VB o VE 5.6 k2 1.2 kM 1.60 V

Q: How many 10-kilo-ohm resistors should you connect in parallel to get an equivalent resistance of 1.2...

A: We know that whenever equal value resistors are connected in parallel then the equivalent resistance...

Q: エ-I」F 2 0 (stjl)I - 20 /0* + (I,-I,)>6 4っ-Fz)+(stj)Ig=o GI3ニI, -I。 o (6-j)I-エco(3) Fo= I2-Ig.

Q: Three identical capacitors are connected in delta to a 408 V, 50Hz, 3-phase supply. If the line curr...

Q: For the diode circuit of the figure below: 1. Determine v, and sketch its waveform for at least 4 cy...

A: We need to find out output voltage for given rectifier circuit

Q: fixed bias circuit shown in figure uses a silicon transistor with VBE = 0.7V. Find the collector cur...

A: In this question we will find collector current Ic...

Q: analog voltmeter h-

A: Note- “Since you have asked multiple questions, we will solve the first question for you. If you wan...

Q: S1.34MH C =7 GVEN ; Pe = 1. 097 fw ; Rfi of the df is D,54305 and the dt is 'capasifive.

Q: Microwave Oven an open loop or closed loop system?

A: Open Loop System- A control system in which the input of the system does not depends on the output o...

Q: The below diagram shows the De-Sauty method to measure the unknown capacitance (C). Then C, is given...

A: Circuit diagram is given as, Here, R1 and R2 are resistance C is standard capacitance, Cx is capaci...

Q: A 1-phase, 20 km line delivers a load of 12 MW at 22 kV having a lagging p.f. of 0.65 at the receivi...

Q: If f(t) F(w), find the fourier Transform of a. f(4t) b. f(t-9) c. t*f(t/2)

A: We are authorized to answer three sub-parts at a time, since you have not mentioned which part you a...

Q: shows a BCD counter that produces a four-bit output representing the BCD code for the number of puls...

A: BCD - counter that counts from (0000)2 to (1001)2 a) xa = high when BCD counter value = 2,3 or 9 b)...

Q: A battery has an emf of 25.0 V. The terminal voltage Mof the battery is 12 V when it is delivering 2...

Q: Determine the values of i1, i2 and i3 for the following figure. 4 ΚΩ 8 ΚΩ 2 ΚΩ 100 V i 4 mA iz 2i, (...

Q: A 6A current source drives a load consisting a parallel combination of R1 = 60 N and R2 = 10N. Deter...

A: The correct answer is Option E. Explanation provided below. Please go through it.

Q: Suppose a CT signal x(t) = 2[u(t-2) – u(t+1)] has a transform X(s). a) If Ya(s) = e^-5s *sX(s), dete...

Q: Determine the total charge transferred over the time interval of 0 < t< 9 seconds whet i(t) = (1/2) ...

A: The solution is given below

Q: Determine the base voltage VB in the circuit. * F15 Vcc R 22 k2 RC 1.5 k2 B = 150, R2 4.7 k2 SRE 680...

A: Base Voltage: It is the value of voltage that is connected to the base terminal of the BJT. It is de...

Q: 6. Implement the following equation: Y = ABC + ABC + ABC + ABC a. Using AND, OR, and NOT gates as fe...

A: Implement the following equations

Q: 4.71 In the circuit shown in the image below, if R1 = 3.1 kQ, R2 = 57 kN, and V1 9.5 V, determine th...

Q: Find the differential equations of every given equations constant/s. using elimination the arbitrary

A: Solution- 1) Given, y = C1eaxcosbx+C2eaxsinbx y = eaxC1cosbx+C2sinbx .................1 We have d ...

Q: The voltage and current at the terminals of an auto- mobile battery during a charge cycle are shown ...

Q: E1 +22 V 三 R, 340 V R1 R3 18 N E, = +22 V +

Q: 20/0º V ji N Vị V2 50 330 1Ω. -j1 N= 2/0° A

A: The solution is given below

Q: Wendy and John have joined your study group. Because neither has any previous experience with basic ...

A: In this problem, the difference between the power units VA and W are explained.

Q: Use current divider rule to determine the currents in two resistors of 302 and 602 connected in para...

A: Current divider rule applies when there are two or more resistors in parallel. In the given question...

Q: Use the mesh current method to calculate the power delivered by the dependent voltage source in the ...

Q: 10.Analyze the following sequential circuits (derive the state transition table and the state diagra...

A: The solution is given below

Q: find the Fourier serjes

Q: H,

Q: i = 12.5(1-e-t/CR) You have been asked to determine the time taken for the current to rise f...

A: Given, i=12.5(1-e-t/CR)R=140C=90i1=1 Ai2=2 A

Q: Determine the input impedance of the given amplifier, if the open-loop input impedance is 1MΩ

A: Amplifier- A device which is used to amplify or modify or increase any signal (voltage, current, etc...

Q: 1.) Using internet (google) or Textbook or Reference book of Digital Electronics, Determine the foll...

A: (a) 3-INPUT NAND GATE: The 7400 series of logic ICs is a well-liked set that can be obtained from a ...

Q: An incandescent lamp is rated 150 watts and is connected to a 120-volt supply. What is the resistanc...

Q: 3. A voltage source with internal resistance, 40 and load resistance, 60 is shown in figure 3. A 50 ...

Q: What is the dimensioning system shown in the figure below? +1.31 67 .31 .51

Q: Decimal Ex Binary Addition Addition 3+5 0011 + 0101 4 + 1 8 + 3 2+4 0010 + 0100 0 +7 0000 + 0111 8 +...

A: The complete table for binary addition is

Q: 1) The required sampling frequency to get ten samples/cycle for a signal that has a baseband of 15 k...

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please su...

Q: 7. Draw the polyphase implementation of x(n) y(m) 1+ 22-1 + 32-2 + 4z-3 + 5z-4 + 6z-5 + 7z-6

A: polyphase implementation is define as the sampling rate conversation which is a very efficient way o...

Q: Q7: For the circuit in Fig 7, find i, iy, and the power dissipated by (absorbed by) the 3 S resistor...

A: In this question We need to determine the currents ix and iy as shown in the circuit. Power absorb ...

Q: 5 A ww + V, 3V, 10 2 O 10 A 5Ω ww

Q: If a current of 5 A flows through a long wire, find the magnetizing force produced 2 cm away from th...

A: Magnetizing Force The sum of all the magnetic flux lines present in the magnetic field is used to de...

Q: 1. Calculate the power delivered to a load at t = 3 ms, if a current passed through the load and a v...

A: Given, Current pass through the load, i=5 cos 60πt A Voltage across the load, v=3i V At time, t = 3 ...

Q: 44) When doing delta-to-wye conversions A) if the resistances are equal in one configuration, then t...

A: From the delta star conversion formulas decide which statement is correct.

Q: An electric lamp whose resistance, when in use, is 2 0 is connected to the terminals of a dry cell w...

Q: 1. For the circuit shown below, a. determine the current I, by the nodal analysis. 12 2 3Ω 24 V 15 V

Q: (b) Figure below shows a ring distributor with interconnector BD having resistance 0.04 Q. The suppl...

Q: electrostatic force?

A: Given that q1=2.8μCq2=-6.2μC

Q: hQ4 Redue the block diag shown in fis to a singe ran block. { G3 { Gut

A: In this question, Find the single block diagram of the given system. We know closed loop transfer ...

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

A coil of wire having a value of (6 + j9) ohms is connected in series with a
capacitive reactance Xc, and this series combination is then connected in
parallel with a resistor R. If the equivalent impedance of the circuit is 5 S
o. Calculate the values of Xc and R.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A coil of wire having a value of (5 + j8) ohms is connected in series with acapacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 4 /0 o ohms, calculate the values of Xc and R.
A coil of wire having a value of (5 + j8) ohms is connected in series with a capacitive reactance Xc, and this series combination is then connected in parallel with a resistor R. If the equivalent impedance of the circuit is 4 /0o ohms, calculate the values of Xc and R.
A series circuit consists of a resistance of 10 ohms, an inductance of 200/π mH, and capacitance of 1000/π μF. Calculate (a) the current flowing in the circuit if the supply voltage is 200 V, 50 Hz, (b) the power factor of the circuit, (c) the power drawn from the supply. Also, draw the phasor diagram.
A resistor of 6 ohms and an unknown impedance coil in series draws 12 A from a 120 V, 60 Hz line. If the real power taken from the line is 1152 Watts, what is the coil inductance?
A source whose voltage is ? (?) = 50√2 cos (?? + 30 °) ? supplies a load ofimpedance ? = (4 + ?3) Ω. Saber is intended to: a) the active, reactive and apparent powerconsumed by the load. b) a capacitor power that must be installed in parallelwith the load to raise its power factor to 0.97 delayed.
A series circuit consists of resistance of 10 ohm, an inductance of 200/π mH and capacitance of 1000/π μF . Calculate (a) the current flowing in the circuit if supply voltage is 200 V, 50 Hz, (b) power factor of the circuit, (c) power drawn from the supply. Also draw the phasor diagram.
An air-cored choking coil is subjected to an alternating voltage of 100 V. The current taken is 0.1 A and the power factor 0.2 when the frequency is 50 Hz. Find the capacitance which, if placed in parallel with the coil, will cause the main current to be a minimum. What will be the impedance of this parallel combination (a) for currents of frequency 50 (b) for currents of frequency 40?
What is the equation of the current in B in the function of sin given that Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by π/3 radians and the total linecurrent is 23.4 amp. (rms).
A resistance of 16 Ω is connected in series with a pure inductance of 39.9 mH and the circuit is connected to a 100 V, 50 Hz, sinusoidal supply. Calculate the phase angle of the impedance. Give your answer as a number without units to 0 decimal places.
A choke coil of resistance 8 ohm and inductance 0.15 H is connected in series with a capacitor of capacitance 125 ?? across a 230-V, 50- Hz supply. Calculate: (a) the inductive reactance, (b) capacitive reactance, (c) impedance, (d) current, (e) voltage across the coil and the capacitor, respectively. (f) phase difference between the current and the supply voltage.
For the configuration shown in the figure below, determine Zi if Vs = 40 mV, Sense = 0.5 kΩ, and Ii = 20 µA
The resistance and inductance of a coil can be obtained by connecting the coil in series with a known resistance R and measuring the coil voltage Vcoil, the resistor voltage VR and the total voltage V. The frequency must also be known, but the phase angles of the voltages are not known. Given that f = 60Hz , R = 10 ohm Vcoil = 22.4 V. VR = 20 V and v = 36v , find the resistance and inductance of the coil.