Llä 4Q1: For the circuit shown, use nodal* analysis to find i1 through i42 A4 A5010Ω10Ω503 5Ai1= 4 A, 12= 2 A, 13= -1 A, 14= 2 ANone of the mentionedi1= -4 A, i2= 2 A, 13= 1 A, i4= -2 Ai1= 4 A, i2= 2 A, 13= 2 A, 14= 3 Ai1= 4 A, 12= 2 A , 13= 2 A, 14= 1 A Owwwwww

Answered: Image /qna-images/answer/5d3a3b36-8bdc-40e9-a988-5635b4bdd6e0.jpg

Answered: Q1: For the circuit shown, use nodal…

Q1: For the circuit shown, use nodal analysis to find i1 through i4 Lä 4 2 A 4 A 10 2 10 2 5 A i1= 4 A, i2= 2 A, 13= -1 A, 14= 2 A O ww %24

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i have a question here. can you please explain on what basis u put what u put in the numerator and denominator when u did nodal analysis? also when can i and when can't i use nodal analysis to solve it this way? but most importantly i dont understand how the equations in nodal analysis were derived. i dont get how using voltage division rule u also used 2/2+1 i dont understand this either so please explain these points extensively. also can vmilman be used here to solve this?
Determine I4 using Source Transformation show complete solution
The solution looks incorrect. For node voltage 3 analysis it should be in respect to node 3 not node 2, your equation seemed to be off at at least that point I'm gonna continue checking but it doesn't make sense physics wise the way you're doing your node analysis. It honestly looks like you plugged in the value for i-1 instead of making an equation for node 3 which would be V3 - V-2 divided by 1. If I am incorrect please explain why
Find v1, v2, i1, i2, i3, i4, i5, and i6
With SW1 open, what is the norton equivalent circuit seen by RL? It should not be in terms of the unknown voltage and current (Va and Ia). Note that: with the SW1 closed, I1 = 2A.
Hey please help me out here. Use mesh analysis to setup an equation of the following. AI1+BI2=-3 Please note that the current following between those loops is Ix
Complete Solution(Auto-like or approved) Given: VR1=12V VR2=12V PR3=12mV Find: RT, R1, R2, R3 IT, IR1, IR2, IR3 VT, VR3 PR1, PR2
The voltage Vab in the circuit shown below is Select one: a. I1 = -6A, I2 = -5A b. I1 = -6A, I2 = 2 A c. I1 = 5A, I2 = -6A d. I1 = 2A, I2 = -6A
Using the circuit, determine thevenin’s voltage(Vth) and thevenin's resistance(Rth) for load resistor R1. Then solve for I1. Draw all diagrams.
Circuits 1 and 2 are connected at their terminals B and D. We are given the following values: R1 = 8 Ω, R2 = 5 Ω, R3 = 4 Ω, V1 = 10 V, I1 = 3.5 A, and I2 = 3 A. Using nodal analysis, we can derive nodal equations for node C and supernode V1 in terms of the nodal voltages VA, VB and VC. From the circuit, we can get the relationship V1=VA−VB and can be re-written to the form: a0VA + b0VB + c0VC= d0 --> (−1)VA +(1)VB + (0)VC = 10 V1 is also a supernode that combines nodes A and B. We can derive a nodal equation and rewrite it to the similar form: a1VA + b1VB+ c1VC = d1. Similarly, for node C, nodal equation can be derived and written into similar form: a2VA+ b2VB + c2VC = d2 Determine value of a1, b1, c1, and d1 as well as value of a2, b2, c2, and d2, respectively.
Hi, I have been given this circuit to analyse (see picture attached) and I solved the first part using KVL by finding i1= +1.984A, i2= - 0.215 and i3= -1.769. I now need to find Vab for which I have been given the solution: VAB = VAC + VCB= (2 – i1) + (4 + 3 i2). What I don't understand is why in this equation there is a minus in front i1. When I did the same equation but I had a plus I didn't get the right result, but I don't see why Vac seems to be a subtraction rather than a sum. I hope you can help me figure this out.
Consider the circuit in the figure. Use the included current directions (arrows) and component labels. a) Which of the following equations would be the correct equation for the junction labeled c? - I1=I2+I5 - I2=I1+I3 - I1=I2+I3 - I1=I2+I4 B) Which of the following equations would be the correct equation for the junction labeled d? - I3=I4+I5 - I3+I4=I6 - I3+I4=I5 - I3+I5=I4 C)Which equation for the junction labeled g? - I6+I5=I4 - I6+I4=I5 - I6+I4=I6 - I6=I4+I5 D) Now you have the junction specifying each current. What is the accurate representation of the loop a=>b=>c=>h=>a? E) What is the accurate representation of the loop equation a=>b=>c=>d=>g=>h=>a? F)What is the accurate representation of the loop equation for loop d=>e=>=>g=>d? (Make sure you follow the directions of the currents drawn)