Q1/ For the state of plane stress shown below, construct and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa sheat stress tal stress aximim Hpla 100 kPa

Q1/ For the state of plane stress shown below, construct and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa sheat stress tal stress aximim Hpla 100 kPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the xy axes, that is, determine crv, tr(_, and t. Show the results on a sketch of an clement oriented at B = 10
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 55 MN/m2 tension respectively. The shear stress across these planes is 25 MN/m2 (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 25o to the plane of greater principal stress. And also verify the answer by drawing the Mohr’s circle.
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 50 MN/m2 tension respectively. The shear stress across these planes is 30 MN/m? (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 30° to the plane of greater principal stress. And also verify the answer by drawing the Mohr's circle.
For the given state of stress, determine (a) the principal planes, (b) the principal stresses. For the given state of stress, determine (a) the orienta-tion of the planes of maximum in-plane shearing stress, (b) the maxi-mum in-plane shearing stress, (c) the corresponding normal stress
A rectangular block of material is subjected to a shear stress of 30MN/m2 together with it's associated complementary shear stress. Determine the magnitude of the stresses on a plane inclined at 30 degrees to the directions of the applied stresses,which may be taken as horizontal
For the element shown below, determine: 1- The principal stresses and the maximum in-plane shear stress acting at the point by using equations, then show these stresses on an appropriate sketch. 2- The normal stresses 0 n and ¢ t and the shear stress T nt for element oriented 20° clockwise from the position shown, using Mobhr’s Circle. 75 MPa
At a point on the free surface of a stressed body, thenormal stresses are 20 ksi (T) on a vertical plane and 30 ksi (C) ona horizontal plane. An unknown negative shear stress exists on thevertical plane. The absolute maximum shear stress at the point hasa magnitude of 32 ksi. Determine the principal stresses and theshear stress on the vertical plane at the point.
Given are the major and minor principal stresses at any point within a rock massσ1 = 50 MPa and σ3 = 20 MPaDetermine graphically the magnitude of the stress components acting on a plane that is inclined at an angle of 250to the major principal plane
Determine the principal stresses andmaximum in-plane shear stress of given stresselement.