Q1/ In Fig.1, pressure gage A reads 1.5 kPa (gage). The fluids are at 20C. Determine the elevations z, in meters, of the liquid levels in the open piezometer tubes B and C. The specific weights are YAIR 12.0N/m³, gasoline 6670 N/m³, and y glycerin = 12360 N/m². Air Gasoline Glycerin

Q1/ In Fig.1, pressure gage A reads 1.5 kPa (gage). The fluids are at 20C. Determine the elevations z, in meters, of the liquid levels in the open piezometer tubes B and C. The specific weights are YAIR 12.0N/m³, gasoline 6670 N/m³, and y glycerin = 12360 N/m². Air Gasoline Glycerin

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q3// Design a rectangular tied column of h=2b that can carry an ultimate axial compression force,…

Q: Write an introduction on the topic (Specific Capacity of Liquids)? to a report Heat 11:23 ص

A: In thermodynamics, the topic specific heat capacity of a substance is defined as the heat capacity…

Q: If the man can move the crate, and the tension force is in the cable. The minimum coefficient of…

Q: Calculate the reactions for the shown frame then draw the 40 kN/m 40 kN/m g 2m 2m 2m Q1 bending…

Q: O Q2) Determine the ultimate load Pu that can be applied at eccentricities ex-100mm and ey=125mm for…

A: Given data:- Eccentricity on x-axis, ex = 100 mm Eccentricity on y-axis, ey = 125 mm Diameter of…

Q: Prepare a data sheet & calculate the cost of painting a top and all sides of a Platform below which…

Q: Q2: In Fig. 1 the upper plate moves upwards in 1.5 m/s and the lower plate moves upwards in1 m/s,…

Q: If Ris the radius of a main circular curve, A is the angle of deflection and a is the polar…

Q: Determine the height to be raised of box mars 12.4kg to gain Potential ener of 133 2 J

Q: Water with v = 1x10-5 m²/s flows at 0.15 m³/s through 200-mm diameter cast iron pipe 500 m long.…

Q: Q1/ It is needed carry water flow (20 m³/sec) in open channel to reach the water to the farthest…

Q: A rectangular channel of (4m) width and the discharge rate is (2 m³/sec) with slope of (1/3000), if…

A: Hydraulic jump A shock wave-like fluctuation in water level is typical beneath weirs and sluice…

Q: or the beam with the cross-section shown and loads as follows: w = 2 kN/m, M = 4 kN-m and P kN, =…

A: Given data:

Q: Write short notes on: (i) Well development (ii) Well spacing

A: Well development Well development is actually defined as the act of cleaning out the clay and the…

Q: 6. Two 8 x 4 x 1 inch blocks of foam are glued together (one block on top of the other) and used to…

Q: Stresses on the Principal Planes 6 the Planes of maximum shearing stress the Planes whose normals…

Q: Bernoulli's

A: Essentially a pump adds energy to a system and a turbine takes it away. Therefore typically in the…

Q: Design a reinforcement of a doubly reinforced beam if the beam has a size of 425 mm x 600 mm. Use fc…

Q: Determine the equivalent ground length of the canal.

A: This question is from Surveying.

Q: 2. Obtain the moment of inertia of the composite area about the specified x and y axes.

A: Moment of inertia of rectangular area when axis passing through baseI=bh33Moment of inertia of…

Q: 1. Given the data as shown in the figure, determine the governing diameter of the solid shaft. Use 2…

Q: Tutorial Problem No. 12.1 fra 1. Perform the following indicated operations: (a) (60+j80) + (30-j…

A: As per guidelines we need to answer only first question so please repost rest questions separately.…

Q: zzle angle is 20° blade speed 183 power lost by fa g bearing friction nd (1) The net p he exhaust

Q: 2.) Determine the maximum load "w" (kN/m) that the box section can carry when used in a simply…

Q: Determine the height to be raised of box mars 12.4kg to gain Potential energy of 133 2 J

A: Introduction : The given question is related with solid mechanics . In this question we are provide…

Q: 10-25. In preparation for a public hearing on a proposed interstate bypass at Non- troppo, Michigan…

Q: 4.) Determine the value of El(y) midway between supports for the overhanging beam as shown using the…

Q: (1162) Determine the midspan deflection for the beam and I = 15 x 10² min ² GooN/m 3m 3m shown? use…

Q: 3 m 3 m 60 kN/m 60 kN/m 20 kN/m 20 kN

A: Q1: C Q2: B

Q: Show complete Solution. 1) INTERSECTION. Given the following data for an intersection problem,…

A: To Determine Coordinates of point A.

Q: 1. State the major ideas of RMR and Q system, and tell their differences. (

A: Rock Mass Rating system(RMR) is also known as Geomechanics Classification.

Q: The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is…

A: Given Data:Outer dia= 75mminner dia= 60mmLength = 2.5mEs=200GpaV=3h=4

Q: A singly-contracted weir 1.5m high is located in a 5m wide rectangular channel with a measured…

A: Height of weir,H=1.5 m Width of channel,B= 5m Discharge, Q=2.3 m3/s

Q: (Trilateration): In a trilateration network one of the triangles has the following data: AB = 600m,…

Q: 11-Determine the greatest angle u so that the ladder does not slip when it supports the 75-kg man in…

Q: Q4/ Determine the state of flow for the following cases: 1. Rectangular channel with area 4 m²,…

Q: Q2/ The hydraulic jump occurred in an open rectangular channel with a length of 3.5 m. Assume Froud…

A: As per bartleby guidelines experts are allowed to solve only first three subparts. Please post…

Q: Q1: Determine the volume of earthwork to be excavated for the plot shown in fig 1. The formation…

A: This question belongs to subject estimation costing and valuation. In this question we find out…

Q: 2. A rural community of 15000 persons generates refuse at an average rate of 5 lb / capita/day. A 25…

Q: Calculate th

Q: Determine the amount of water needed to achieved the normal consistency of 650 grams cement by using…

A: The amount of water required to be mixed in cement to make a cement paste such that when the sample…

Q: Q4/ Axial water turbine installed on a river barrage. Head drop between the water source level and…

Q: 1. Determine the Specific gravity of aggregate based on the following values: Mass of empty…

A: Given data Mass of empty container: M1 kg Mass of container+ Aggregate: M2 kg Mass of container+…

Q: a. Do the amount of RHA affect the compressive strength? How so? b. Does the admixture affect the…

A: The rice husk ash is a by-product from the Agricultural field which is used as pozzolanic reactive…

Q: Q.24 Assertion (A): When a sharp horizontal curve is to be introduced on a road which already has…

A: Assertion (A) : When a sharp horizontal curve is to be introduced on a road which already has the…

Q: A batch plant mixes 80 tons of asphalt mix with an average mixing cycle time of 1 min. Plant…

Q: sand

Q: 28 KN AB= BD DF= FG= 30 KN 1.25 m || B C 42 KN O E 1.55 m 98 KN F 1.10 m EG = CE= AC = BC= 2.65 m Av…

Q: 179. For doubly-symmetric shapes with slender elements and adequate torsional unbraced length, which…

A: 179. For double symmetric shapes with slender elements and adequate torsional unbraced length,…

Q: The block speed when it has moved 12 cm down the surface. The distance down the incline surface from…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Q1/ In Fig.1, pressure gage A reads 1.5 kPa (gage). The fluids
are at 20C. Determine the elevations z, in meters, of the liquid
levels in the open piezometer tubes B and C.
The specific weights are YAIR 12.0N/m³, gasoline 6670 N/m³,
and y glycerin = 12360 N/m³.
2m
Air
Gasoline
Glycerin
200

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The mercury manometer in the Figure below is connected to the inlet and outlet ofa water pump (the left side to the inlet and the right side to the outlet). Assuming thatthe inlet and outlet are at the same elevation, determine the pressure increase for thepump.
an open circular vessel is 1m in diameter and 2m height. it contains water filled to a depth of 1.5m. if the cylinder rotates about its vertical axis, what is the pressure intensity at the corner of the bottom if w= 6 radians/second Unit of the correct answer: kPa
An open rectangular tank 2m by 2m and 3.5m high contains 3 layers of liquids with specific gravities of 1.3, 1.0, and 0.9, and heights of 1.0m, 1.5m, and 0.5m respectively. An opening with an area of 25 cm2 and coefficient of discharge of 0.711 is situated at the bottom of the tank. 1. How long will it take to discharge the bottom layer of the liquids? in seconds 2. What is the total time to discharge the bottom and the middle layers of the liquids? in seconds 3. What would be the total time to discharge all the liquids? in seconds
Calculate the flow rate of the system by accepting the fluid passing through the reservoir-pipe system shown in the figure as ideal. D1 = 0.5 m,Since D2 = 0.30 m and D3 = 0.40 m, determine the velocity heights in each pipe. In pressure gauge pipesCalculate and show water levels in the figure (pressure gauge pipes are externally connected to pipes 1 and 2, but 3.Note that the tip of the manometer pipe in the pipe is turned to the flow direction). The relative energy and relative energy of the systemDraw the piezometer lines.
Q2) Calculate the value of pressure ∆p onside the rain water droplet , if we knowthe radius R=0.2mm and the surface tensionδ = 0.074 N/M
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids - castor oil (0.96) and water. Considerinh a unit-width of the gate, apoly the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 20ft.
The system in Fig. P2.48 is open to 1 atm on the right side. (a) If L = 120 cm, what is the air pressure in con tainer A? (b) Conversely, if Pa = 135 kPa, what is the length L?
A pressure gage 6m above the bottom of the tank containing a liquidreads 90kPa. Another gage height 4m reads 103 kPa. Determine thespecific weight of the liquid.
HYDRAULICS LABORATORY EXPERIMENT NO.4 3. Using the value of Cd, which you have obtained by experiment, determine the throat diameter of a Venturi meter which would measure a flow of 0.40 m3/s in a pipe of 0.60 meter diameter with a differential head of 0.80 meter
Figure 2 represents an oil storage drum that is open to the atmosphere at the top. Some water was accidentally pumped into the tank and settled to the bottom as shown in the Figure 2. Calculate the depth of the water h2 if the pressure gage at the bottom reads 158 kPa (gage). The total depth hT = 18.0 m
Estimate the height to which water will rise or fall in a capillary tube of diameter 3 mm. Use ? = 0.0728 N/m and ? = 9,810 N/m3for water.