Q1/ In the circuit shown below, the zener diode used has the following specifications : Vz= 12 volt, Izk = 0.25 mA and PD( max ) = 1.5 watt.Find the limits of voltage . regulation done by the zener diode Izener(max) = 125 mA R1 = 200 ohm www V in RL Zener diode regulation vin from Vin(min) 12.050 v to Vin(max)= 35.050 Volt false True

Q1/ In the circuit shown below, the zener diode used has the following specifications : Vz= 12 volt, Izk = 0.25 mA and PD( max ) = 1.5 watt.Find the limits of voltage . regulation done by the zener diode Izener(max) = 125 mA R1 = 200 ohm www V in RL Zener diode regulation vin from Vin(min) 12.050 v to Vin(max)= 35.050 Volt false True

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Use the DC power supply VSS of +9.0 Volts.Calculate the the forward turn-on voltage of the diode..
Calculate the power rating of a zener diode connected across load working in reverse biased condition when the breakdown occurs at the current twice the test current, where VZ = 30 V, VZK =28.5V, IZK= 2mA, IZ= 10mA . Also calculate the minimum load resistance value with input voltage at Vs= 60 V and series resistance 450ohms.
VS = 17,6 V, R1 = 10 kΩ, R2 = 10 kΩ, RL = 23,8 kΩ and Vzener = 6,1 Volts. What is the power dissipated in Zener diode in mW?
A 10 V Zener diode is used to regulate the voltage across a variable loadresistor. The input voltage Vs varies between 13 and16 V. The loadcurrent (??) varies between 10 and 85 mA. The minimum Zener current is15 mA. Findi. The maximum value of Rsii. The maximum power dissipated by the Zener diode, using the value ofRs.
In the given system; Va, Vb, Vc effective value is 220V, Ly=300 mH and Ry=22 Ohms.It was observed that the yuk current is continuous when the tristorier is triggered for alpha=65 degrees; and D1the average value of the diode current was calculated as ID1 avg = 1.703A.Accordingly, calculate the average value of the current flowing through T3. IT3_ avg=?
a. Using standard resistor values, what value of R1 is needed to achieve 1.18V ±0.01V at Vout? b. Using the R1 value chosen in (a) part, what happens to the voltage Vout when a load resistance of 10K is added (between Vout and ground). c. What is the minimum value of load resistance required for correct operation Zener diode is used in place of si diode. Or you can assume zener current according to requirement Answer it i will rate
For the values of R1=230, R2=230, R3=400, Vs=15. If the real diode (offset voltage=0.7V) were conduxting, then the value of voltage source Vb should be? solve correct or will dislike
1 - Do the calculation to predict the expected theoretical output waveform of each circuit shown in Figures 5.4 and Figure 5.6. Assume that the diodes used in the circuit are ideal. ? NOTice that do not copy the answer from and websit even from bartleby beacause there is some one who already post the question on chegg and bartleby but i do not like there answer please and give me your answer if you can answer it thank you on advance
1. What is Diode Clippers 2. What are the configuration you have learn in this activity? show diagram / show actual connection 3. What is the output waveform 4. What is Diode Clampers 5. What are the configuration you have learn in this activity? show diagram / show actual connection 6. What is the output waveform 7. What is Zener and its function?
Calculate the average value of the output voltage for ? = 60 ° of a three-phase full-wave thyristor rectifier operating on a network with phase neutral voltage of 100V.
Zener voltage, VZ = 6.1V and incremental resistance, rz = 0 a) Determine the value of Ri such that the Zener diode remains in breakdown if the load current varies from IL = 20 to 200 mA and if the input voltage varies from VI = 8.6 to 10V. Assume IZ(min) = 0.1IZ(max). b) Determine the power rating required for the Zener diode and the load resistor. c) If the position of Zener diode were changed to be in forward bias region, will the voltage regulator still work properly? Justify your answer