Q1) Oil of specific gravity s.g = 0.8 is drawn into the pump, the pressure at A is -20 kpa and at B is 100 kpa. Calculate the power input of the pump if the discharge at B is 0.07 m'/s and the pipe diameter is 80 mm and h = 2.5 m as shown in Fig.1. Neglect friction losses. Take the efficiency of the pump 0.85 %3!

Q1) Oil of specific gravity s.g = 0.8 is drawn into the pump, the pressure at A is -20 kpa and at B is 100 kpa. Calculate the power input of the pump if the discharge at B is 0.07 m'/s and the pipe diameter is 80 mm and h = 2.5 m as shown in Fig.1. Neglect friction losses. Take the efficiency of the pump 0.85 %3!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)
A pump draws water from a reservoir and conveys it to another reservoir 30 m above. The suction pipe is 100 mm in diameter and 10 m long while the delivery pipe is 100 mm in diamter and 150 m long. if the the velocity in the pipe is 3 m/s, the friction factor of the pipe 0.008, and the pump and motor efficiencies are 85 % and 92 %, respectively. Assume height of pump/motor negliglible. Q1. Calculate the gauge pressure at the pump's inlet (at C) (kN/m2) Q2. Calculate the gauge pressure at the pump's outlet (at D) (kN/m2) Q3. Calculate input power to motor (kW)
Oil of specific gravity 0.750 is pumped from a tank over a hill through a 24′′ pipe with the pressure at the top of the hill maintained at 25.5 psi. The summit is 250 ft above the surface of the oil in the tank, and oil is pumped at the rate of 22.0 cfs. If the lost head from tank to summit is 15.7 ft, what horsepower must the pump supply to the liquid? Indicate the Free Body Diagram
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
Calculate the minimal head of the pump required to pump 1 m³ of water per second to the height 10 m trough a pipe with cross sectional area 0.1 m². Assume constant friction coefficient f = 0.04 and neglect all losses in fittings. The pump head is the gravity head plus losses and so it can be found?
What power must be supplied by the pump to the flow ifwater (T =20°C) is pumped through the 300 mm steel pipefrom the lower tank to the upper one at a rate of 0.314 m^3/s?
The task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated platform as shown. The goal is to fill up that 16.49 m by 2.23 m by 6.36 m tank (TANK A) within 11.5 mins (from empty to full). Your budget is limited to 605,000 pesos. Head loss on pipe due to friction is 1.23 meters per 1 meter of pipe. Because it's Fluid Machinery and not Engineering Economics, it's ok for your design to exceed the budget BUT YOU HAVE TO JUSTIFY IT.
The task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated platform as shown. The goal is to fill up that 16.49 m by 2.23 m by 6.36 m tank (TANK A) within 11.5 mins (from empty to full). Your budget is limited to 605,000 pesos. Head loss on pipe due to friction is 1.23 meters per 1 meter of pipe. Because it's Fluid Machinery and not Engineering Economics, it's ok for your design to exceed the budget BUT YOU HAVE TO JUSTIFY IT. The pictures I will post is the guide to answer Its okay if the answer is computerized
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The sucLon pipe is 350mm in diameter and 12m in length and the delivery pipe is 550mm in diameter and 40m in length. Calculate:(a) The maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa (gauge) (b) the energy to be supplied by the pump per unit mass of water transferred (c) The input power required by the pump, which is 60 % efficient
A pump is delivering 160 liters per second of water using an impeller diameter of 254mm and operating at a speed of 1800 rpm. If the speed is held constant and the impeller diameter is changed to 203.2 mm, what is the new discharged of the pump in liters per second?(128 L/s)
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A