Q1) The apparent power entering a certain load Z is 250 VA at a power factor of 0.8 leading. If the RMS phasor voltage of the source is 125 V at 1 MHz: (a) Determine Irms going into the load (b) Determine S into the load (c) Determine Z (d) The equivalent impedance of the load circuit should be of the form Z =R+ jwL or Z = R - j/wC. Determine the value of L or C, whichever is applicable.

Q1) The apparent power entering a certain load Z is 250 VA at a power factor of 0.8 leading. If the RMS phasor voltage of the source is 125 V at 1 MHz: (a) Determine Irms going into the load (b) Determine S into the load (c) Determine Z (d) The equivalent impedance of the load circuit should be of the form Z =R+ jwL or Z = R - j/wC. Determine the value of L or C, whichever is applicable.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2MCQ: If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by...

See similar textbooks

Similar questions

Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2 Ohms, L=5 milliHenry, C=200 microFarad, V=70sin(wt) volts. Determine the watts and VARs for the capacitor, resistor, inductor, and source. Also find power factor. Given R1=9 Ohms, R2=1 Ohms, L= 3 milliHenries, and a sinusoidal voltage source of 5 volts amplitude and 60 Hz freqency all in series. Determine the voltage across R1: magnitude (volts), frequency (Hz), and phase (degrees).
A load with a voltage amplitude of 50 Hz 300 V rms at its terminals consumes 28.98 kW at a back power factor of 0.69. If a 225.87 microfarad capacitor is connected parallel to the terminals of this load, how much will the amplitude of the current drawn from the line decrease?
For the frequency-domain circuit , calculate: 1. a) the rms magnitude of Vo;2. b) the average power dissipated in the 9 Ω resistor;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to the 9 Ω load resistor.
The values of the parameters in the circuit shown are L1=8 mH; L2=2 mH; k=0.75; Rg=1 Ω; and RL=7 Ω. Ifvg=542 cos 1000t V, find 1. a) the rms magnitude of vo;2. b) the average power delivered to RL;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to RL.
A supply voltage v given by v = (240 sin 314t + 40 sin 942t + 30 sin 1570t) volts is applied to a circuit comprising a resistance of 12 ohmconnected in series with a coil of inductance 9.55 mH. Determine (a) an expression to represent the instantaneous value of the current, (b) the rms voltage, (c) the rms current, (d) the power dissipated, and (e) the overall power factor.
Calculate the active power, reactive power, power factor, Reactive factor if: v=100 cos (wt+150) V and i=4 cos (wt-1050) V Note: Enter the angle in radians. (rad * pi/180) Consider V and I given in the problem represents Vrms and Irms Active Power, P = Vrms Irms cos(θv – θi) Reactive Power, Q = Vrms Irms sin(θv – θi) Power factor (pf) = cos(θv – θi) Reactive factor (rf) = sin(θv – θi)
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
When connected to a 120 V (rms), 60-Hz power line, a load absorbs 4kW at a lagging power factor of 0.8. Find the value of Capacitance, C, necessary to raise the power factor to 0.95 lagging.
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
Understand ac power concepts, their relationships to one another, and how to calculate them in a circuitA load consisting of a 1.35 kΩ resistor in parallel with a 405 mH inductor is connected across the terminals of a sinusoidal voltage source vg, where vg = 90 cos 2500t V. Find 1. a) the average power delivered to the load,2. b) the reactive power for the load,3. c) the apparent power for the load, and4. d) the power factor of the load.