Q1: The bode diagram of the following open-loop T.F is as shown in Fig. below: K GH(s)= s(s+2)(s+2) B Dagam 100 110 120 140 150 160 F y 1- Find phase margin, gain margin, gain crossover frequency, phase Crossover frequency, delay margin and comment on the stability 2- Find the value of K for oi =3 rad/ sec 3- Find the value of K for G.M = 30 db 4- Find the value of K for P.M =50 deg %3D Phese eg

Q1: The bode diagram of the following open-loop T.F is as shown in Fig. below: K GH(s)= s(s+2)(s+2) B Dagam 100 110 120 140 150 160 F y 1- Find phase margin, gain margin, gain crossover frequency, phase Crossover frequency, delay margin and comment on the stability 2- Find the value of K for oi =3 rad/ sec 3- Find the value of K for G.M = 30 db 4- Find the value of K for P.M =50 deg %3D Phese eg

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The transfer function for the bandreject filter shown in isH(s)=s2+(1LC)s2+(RL)s+(1LC).Show that if the circuit is scaled in both magnitude and frequency, thetransfer function of the scaled circuit is equal to the transfer function ofthe unscaled circuit with s replaced by (s/kf), where kf is the frequencyscale factor.
a) from the rootlocus fig , Write the open loop transfer function of the system,b) What is the value of K for critical damped response?c) What is the range of K for stable closed-loop system?d) Determine damping ratio and ( Wn ) of the closed loop system for K=10.e) Sketch the approximate graph of the Bode magnitude of the transfer function (use K=100).
Given the filter circuit below. Calculate the transfer function, H ( f ), in terms of R1, R2 and C. Present the final answer in the standard form.
he Bode magnitude plot of H(w) is shown in above figure. Which one can be its transfer function H(s). In the above figure X=16 and Y=24. a. H(s) = 1920s / [(s + 16).(s+24)] b. H(s) = 5760s / [(s + 16).(s+24)] c. H(s) = 1152s / [(s + 32).(s+48)] d. H(s) = 2560s / [(s + 16).(s+24)] e. H(s) = 2304s / [(s + 32).(s+36)] f. H(s) = 3840s / [(s + 16).(s+24)] g. H(s) = 384s / [(s + 16).(s+24)] h. H(s) = 1536s / [(s + 32).(s+72)]
Find the transfer function of the circuit below and draw the bade plot indicating the cut off frequencies in radians/sec.
find the transfer function of the pressure at resistance R1 over the input pressure V, VR1/V
Simplify the block diagram as shown in Fig. Q1(c) into a single block and determine the overall transfer function, C(s) / R(s) .
Draw the Bode Diagram for the system given the transfer function below. Use the Bode diagram to interpret the stability of the system. ( I would appreciate it if you could help quickly :) )
a-) Determine the zero and poles of the circuit given above by obtaining the transfer function as H(s) = Vout(s) / Vin(s) (Assume the initial values of the energy storage elements are zero). b-) Using the transfer function obtained in the previous option, draw the approximate total amplitude response graph of this function with the help of BODE curves. In these drawings, the total amplitude response equations of the system, the amplitude response graphs of each component in these equations, and the frequency values in the total graphs drawn should be included.
A series RLC circuit is formed using component values R=100 and L=1.5 mH, together with a source that provides a sinusoidal voltage Vs (t). If the quality factor in resonance condition is Q0 = 7, determine: a) the magnitude of the impedance at 500 Mrad s-1b) the current that circulates if vs (t) = 2,5V cos (425 ×10 6t) Note: Vent (input voltage). Vsal (output voltage)
We have two filters with transfer functions H 1 (f) and H 2 (f) cascaded in the order 1– 2. Give the expression for the overall transfer function of the cascade. Repeat if the transfer function magnitudes are expressed in decibels denoted as |H 1 ( f )| dB and |H 2 ( f )| dB. What caution concerning H 1 ( f ) must be considered?
The voltage transfer function of either low-pass prototype filtershown isH(s)=1s+1. Show that if either circuit is scaled in both magnitude and frequency, thescaled transfer function isH′(s)=1(s/kf)+1.