Q1:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three forces. Two forces are known in magnitude and direction and shown in the Figure (150 N and 60 N). The third force is passing through the center of the semi-circle (point C). The resultant of all these forces is a single couple (750 N.m) counterclockwise. a) Determine the magnitude and direction of the third force. b) Determine the magnitude of moment (M). c) Replace the couple (M) by two vertical equal forces acting at D and E. d) Replace the force (150 N) by and single force at D and a couple.

Q1:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three forces. Two forces are known in magnitude and direction and shown in the Figure (150 N and 60 N). The third force is passing through the center of the semi-circle (point C). The resultant of all these forces is a single couple (750 N.m) counterclockwise. a) Determine the magnitude and direction of the third force. b) Determine the magnitude of moment (M). c) Replace the couple (M) by two vertical equal forces acting at D and E. d) Replace the force (150 N) by and single force at D and a couple.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m) a) Show the support reactions and load occurring on the rod. b) Do you calculate support reactions? c) Calculate the Normal Force, Shear Force and Moment values by cutting from the points you have determined. d) Draw cross-section impact diagrams? Do you specify the maximum positive and negative moment values? e) Check the cross-sectional influence diagrams with a simple method, briefly explain the control steps.
In the beam depicted above, ?A is a fixed support. The magnitude of ?=365?/?W=365N/m, ?=60?P=60N and all lengths denoted by ?=1.5?a=1.5m. The system is in equilibrium. Using the given sign convention, answer the following questions. a) Calculate the vertical component of the external reaction at ?A in ???????Newtons. b) Calculate the horizontal component of the external reaction at ?A in ???????Newtons. c) Calculate the moment component of the external reaction at ?A in ??????Newton ??????metres. d) Calculate the shear force at point ?B in ???????Newtons. e) Calculate the bending moment at ?B in ??????Newton ??????metres. f) Calculate the shear force at point ?D in ???????Newtons. g) Calculate the bending moment (absolute value) at ?D in ??????Newton ??????metres. h) Calculate the shear force at point ?E in ???????Newtons. i) Calculate the bending moment at ?E in ??????Newton ??????metres. j) Calculate the shear force at point ?H in…
Question: Calculate the vertical reaction force at G and the vertical reaction force at A.
Problem 2) The beam shown in Figure 2 – B is loaded with a 20 kN concentrated load and a 12 kN/muniformly distributed load, determine the following:a) The moment of inertia about the neutral axis.
The coefficient of static friction between the drum and brake bar is μs = 0.4. If the moment M = 35 N ⋅ m, determine the smallest force P that needs to be applied to the brake bar in order to prevent the drum from rotating.Also determine the corresponding horizontal and vertical components of reaction at pin O. Neglect the weight and thickness of the brake bar. The drum has a mass of 25 kg.
In the cage system given in the figure, AB, DE andPressure or pull CB rod forcescalculate by stating that they are. L1(m)=2.1 ,L2(m)=3.2, P1(kN)=65, P2(kN)=57
The gate AB is a quarter circle of 2.5 meters in diameters and 3 meters wide asshown in figure#2. How Find the horizontal component of the resultant hydrostatic forceacting on the gate in kilonewtons. How find the vertical component of the resultant hydrostatic force actingon the gate in kilonewtons, and how to find the location of PH and Pv from hinge A in meters. And if the weight of the gate is 100 Newtons, how find the force “F” just sufficient to preventrotation about hinge A.
The magnitude of the force Q is 896 N. Determine the magnitude of the moment (Nm) of Q about point C. Round off only on the final answer expressed in 3 decimal places.
please i dont have much time solve fast as you can When the angle θ = 90 °, the BE hydraulic cylinder applies a vertical force (F = 3330 N) Newtons to the platform. The mass of the crate is 200 kg and the angular velocity (ω) of AB is 7 (rad / s). First, treat the box and platform as a single body to find the following: The amount of reaction forces at points B and D. Acceleration of the center of the box aG in the x and y direction. Second, after finding the previous requirements, find the following for the platform only: The force of reaction from the box to the platform (Normal force). Minimum static friction coefficient (μs) to ensure the box does not slip. Note: Neglect the weight of the platform and objects AB and CD.
Give me right solution. A closed cylindrical tank 30 cm in diameter and 120 cm high contains 90 cm of liquid SL = 0.80). The rest is air under a pressure of 12 kPag. The above tank is rotated about its geometric axis at the center a rate of 200 RPM. At the above angular speed: Determine the following (a). force on the inside top of the tank in kN. (b) force on the inside bottom of the tank in kN
Beam AC is in equilibrium with loading 100 N at B shown in the figure when β = 45. Determine the unknown forces Ax and Ay at A in x and y direction and Rc perpendicular to the beam AC in y’ direction at C by using the equilibrium equations: ∑ ???= 0 ; ∑ ??y= 0; and ∑ ???= 0 where o is an arbitrary point. (you have three equations to solve three unknowns)
The 8-meter span AC beam made of steel material with a section height of 40 cm and a width of 20 cm carries the mass of m = 50kg at the B point. Assuming that the mass m is at rest (u (0) = 0 m / s) at t = 0 sec and has a displacement of 10 mm (u (0) = 10 mm) in the downward direction in the Single Degree of Freedom system, which is created by neglecting the mass of the beam and supports:a) Write the equation for the mass m.b) Calculate the period (T) of the vibrational motion.c) Calculate the velocity and displacement of the mass m at time t = 3 seconds. g=9.81 m/s2 , Esteel= 200 GPa