67 l allM O 2 o 9:05the test.pdfQ1/ The thermal contact conductance at the interface of two1.5-cm-thick copper plates is measured to be 19,000 W/m2 °C.Determine the thickness of the copper plate whose thermalresistance is equal to the thermal resistance of the interfacebetween the plates. The thermal conductivity of copper k = 401 W/m-°CQ2/ A 4-m-internal-diameter spherical tank made of 1.75-cm-thickstainless steel (k 15 W/m °C) is used to store iced water at 0°C. Thetank is located in a room whose temperature is 35°C. The walls of theroom are also at 35°C. The outer surface of the tank is black, and heattransfer between the outer surface of the tank and the surroundings is bynatural convection and radiation. The convection heat transfercoefficients at the inner and the outer surfaces of the tank are 80 W/m2°C and 10 W/m2 °C, respectively. Determine (a) the rate of heattransfer to the iced water in the tank and (b) the amount of ice at 0°Cthat melts during a 1-h period. The heat of fusion of water atatmospheric pressure is hif 334 kJ/kg.

Given Thermal conductivity, k = 401 W/mK Heat transfer coefficient, h = 19000 W/m2K

Q1/ The thermal contact conductance at the interface of two 1.5-cm-thick copper plates is measured to be 19,000 W/m2· °C. Determine the thickness of the copper plate whose thermal resistance is equal to the thermal resistance of the interface between the plates. The thermal conductivity of copper k = 401 W/n %3D

Q1/ The thermal contact conductance at the interface of two 1.5-cm-thick copper plates is measured to be 19,000 W/m2· °C. Determine the thickness of the copper plate whose thermal resistance is equal to the thermal resistance of the interface between the plates. The thermal conductivity of copper k = 401 W/n %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.38P: 2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from...

See similar textbooks

Similar questions

1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
On a multi-layered square wall, the thermal resistance of the first layer is 0.005 ° C / W, the resistance of the second layer is 0.2 ° C / W, and the third layer is 0.1 ° C / W. The overall temperature gradient in the wall is multilayered from one side. to the other side is 70 ° C. a. Determine the heat flux through the walls. = Answerwatts / m2. b. If the thermal resistance of the second layer is changed to 0.4 ° C / W, what is the effect in% on heat flux, assuming the temperature gradient remains the same? = AnswerAnswer%.
A steam pipe (inner diameter = 150 mm and outer diameter = 160 mm) havingthermal conductivity 58 W/m. °C is covered with two layers of insulation, ofthickness 30 mm and 50 mm respectively and thermal conductivities 0.18 W/m. °Cand 0.09 W/m .°C respectively. The temperature of the inner surface of steam pipeis 320°C and that of the outer surface of the insulation layers is 40°C.Determine the quantity of heat lost per meter length of steam pipe and layercontact temperature,
A steam pipe 50 mm diameter and 2.5 m long has been placed horizontally and exposed to still air at 25 degree Celsius. If the pipe wall temperature is 295 degree Celsius, determine the rate of heat loss. At the mean temperature difference of 160 degree Celsius, the thermo-physical properties of air are k =3.64 * 10 -2 W/m v =30.09 * 10 -6 m2/ P r =0.68 Β =1/160 + 273 = 2.31 * 10^-3/K
Liquid flows in a metal pipe with an inner diameter of D1 = 20 mm and an outer diameter of D2 = 30 mm. The thermal conductivity of the pipe wall is 10 W/m⋅K. The inner surface of the pipe is coated with a thin polyvinylidene chloride (PVDC) lining. Along a length of 95 cm, the pipe outer surface is exposed to convection heat transfer with hot gas, at T∞ = 95° C and h = 6 W/m2 ⋅K, and thermal radiation with a surrounding at Tsurr = 95° C. The emissivity at the pipe outer surface is 0.3. The liquid flowing inside the pipe has a convection heat transfer coefficient of 52 W/m2⋅K. If the outer surface of the pipe is at 86° C, determine the temperature at the PVDC lining and the temperature of the liquid.The ASME Code for Process Piping (ASME B31.3-2014, A323) recommends a maximum temperature for PVDC lining to be 81° C. Does the PVDC lining comply with the recommendation of the code?
A plane wall (0.8 m x 0.6 m) at 10 oC is to be heated by attaching 7-cm-long, 3-mm-diameter pin fins (k=200 W/mK, ρ=5000 kg/m3) to it. nfin=200 fins are to be used in total. Temperature of the surrounding fluid is 100 oC, and the heat transfer coefficient on the surfaces is 35 W/m2K. Total (material + manufacturing) cost of the fins is 850 TL/kg. Fill the table below by neglecting heat transfer from the fin tips. nfin=? a) Fin efficiency b) Fin effectiveness c) Overall fin effectiveness d) Total cost of fins
Two identical aluminum plates with thickness of 30 cm are pressed against each other at an average pressure of 1 atm. The interface, sandwiched between the two plates, is filled with glycerin. On the left outer surface, it is subjected to a uniform heat flux of 7800 W/m2 at a constant temperature of 50°C. On the right outer surface, the temperature is maintained constant at 30°C. Determine the thermal contact conductance of the glycerin at the interface, if the thermal conductivity of the aluminum plates is 237 W/m∙K. Discuss whether the value of the thermal contact conductance is reasonable or not
A total of 10 rectangular aluminum fins (k =203 W/m·K) are placed on the outside flat surface of anelectronic device. Each fin is 100 mm wide, 20 mm highand 4 mm thick. The fins are located parallel to each otherat a center-to-center distance of 8 mm. The temperature atthe outside surface of the electronic device is 60°C. The airis at 20°C, and the heat transfer coefficient is 100 W/m2·K. Determine (a) the rate of heat loss from the electronic device to the surrounding air and (b) the fin effectiveness.
A 1mm thick copper plate (k = 386 W/mK) is sandwhiched between two 5mm thick epoxy boards (k = 0.26 W/mK) that are 15cm x 20cm in size. If the thermal contact conductance on both sides of the copper plate is estimated to be 6000 W/mK, determine the error involved in the total thermal resistance of the plate if the thermal contact conductance are ignored. I.E. what effect does the thermal contact conductance have on the heat transfer rate.
The temperature at the inner and outer surfaces of a boiler wall made of 25 mm thick steel and covered with an insulating material of10 mm thickness are 300 C and 50C respectively. If the thermal conductivities of steel and insulating material are 58W/mC and 0.116W/mC respectively, determine the total resistance through the boiler wall. (Note area of sample boiler wall is 8 m2)