Q1.5 (v6q9-52, Diesel) An ideal cycle has a compression ratio of 18 and a cutoff ratio of 1.5. Determine the maximum air temperature and the rate of heat addition to this cycle when it produces 200 hp of power; the cycle is repeated 1200 times per minute; and the state of the air at the beginning of the compression is 95kPa and 17C. Use constant specific heats at room temperature. Ans 1382K, 227.2kW

Q1.5 (v6q9-52, Diesel) An ideal cycle has a compression ratio of 18 and a cutoff ratio of 1.5. Determine the maximum air temperature and the rate of heat addition to this cycle when it produces 200 hp of power; the cycle is repeated 1200 times per minute; and the state of the air at the beginning of the compression is 95kPa and 17C. Use constant specific heats at room temperature. Ans 1382K, 227.2kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp=1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) calculate the thermal efficiency of the cycle in %? 2) which formula should be used to determine the thermal efficiency of the cycle ?
An ideal Diesel cycle has a maximum cycle tempera¬ture of 2000°C. The state of the air at the beginning of the compression is P1 = 90 kPa and T1 = 15°C. This cycle is exe¬cuted in a four-stroke, eight-cylinder engine with a cylinder bore of 12 cm and a piston stroke of 14 cm. The minimum volume enclosed in the cylinder is 5 percent of the maximum cylinder volume. Determine the power produced by this engine when it is operated at 1500 rpm. Use constant specific heats at room temperature.
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 1950 K. Determine the cutoff ratio. rc =
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2250 K. Determine the compression ratio. r =
(c) In an engine working on the ideal Otto cycle, the pressure and temperature at the beginning of compression are 100 kPa and 40 °C respectively. The ratio of specific heat capacities is 1.4. If the airstandard efficiency of the engine is 50%, determine(i) The compression ratio. (ii) The pressure and temperature at the end of adiabaticcompression.
A Diesel cycle has a compression ratio of 22 and begins its compression at 87 kPa and 15°C. The maximum cycle temperature is 1200°C. Utilize air-standard assumptions. The properties of air at room temperature are R = 0.287 kPa·m3/kg·K, cp = 1.005 kJ/kg·K, cv = 0.718 kJ/kg·K, and k = 1.4. Determine the thermal efficiency of this cycle using variable specific heats at room temperature. Use data from the tables. The thermal efficiency of this cycle is?
An ideal, air-standard Diesel cycle has a compression ratio of 20. The maximum temperature is 2200 K while the air is 320 K and at 105 kPa before compression. Assume that specific heats vary with temperature. 1. Report the temperature after compression in K. 2. Report the cutoff ratio to two decmial places using rounding. 3. Report the amount of heat added to the cycle in kJ/kg to one decimal place using rounding. 4. Report the temperature after isentropic expansion in K to one decimal place using rounding. 5. Report the amount of heat rejected in kJ/kg rounded to one decimal place. 6. Report the net work produced in kJ/kg to the nearest whole number using rounding. 7. Report the overall thermal efficiency as a percentage (0 to 100) to one decimal place using rounding.
If the isentropic compression ratio of a Carnot cycle is 5 and the lower temperature limit of the cycle is 25degree C, determine the power that the engine can produce if the heat added amounts to 45kW. Assume that the cycle is an air standard cycle.
An ideal Diesel cycle has the air inlet temperature and pressure of 19 0C and 92 kPa respectively. The compression ratio is 24:1 while the maximum cycle temperature is 1,225 0C. Take Specific heat at constant pressure and constant volume for air as 1.005 kJ/kg K and 0.714 kJ/kg K respectively. Calculate the absolute temperature after the isentropic compression process to one decimal place and include the correct unit (absolute temperature).
An ideal Otto cycle has a compression ratio of 6. At the beginning of the compression process, air is at 100 kPa and 27°C. If 950 kJ/kg of heat is transferred to the cycle during heat addition process, determine the maximum temperature, in Kelvin, determine the maximum pressure, in kPa, determine the thermal efficiency of the cycle. Apply air-standard assumptions: variable specific heat)
An air-standard Diesel cycle has a compression ratio of 16 and a cut-off ratio of 2.0. At thebeginning of compression, it is p1 = 110 kPa and T1 = 280 K.Determine:(a) The temperature achieved at the end of heat addition.(b) The net work per unit mass.(d) The thermal efficiency.
For an ideal Diesel cycle, (a) Draw the P-v and T-s diagrams (b) Using the fifirst law, fifind the expression for thermal effiffifficiency in terms of enthalpy and internal energy (c) Simplify the expression in (b) using cold air standard assumptions and express it in terms of the compression ratio, cutoff ratio, and the specifific heat ratio.