Q11:design a two input logic circuit (A, B) to implement And, Or,Xor,Complement using Mux and logic gates.
Q: Deber mine ID, Ves, VRS, VRD, Vos Vos + Vth = 2V Kn = 4mA)V? Rs Rp LOV 10v
A: We need to find out current and voltage for given circuit
Q: Answer the following True or False: 1. A direct bandgap material absorbs more light in a given…
A: 1) As the direct bad gap material emits large number of photons than that of indirect band gap…
Q: Give the different excitation table of each type of flip-flop.
A: The excitation table of the SR flip-flop is shown below: The excitation table of the JK flip-flop…
Q: 13. An electromagnet in a generator has the ability to generate a variety of magnetic fields. O True…
A: An electromagnet in a generator has the ability to generate a variety of magnetic fields. Statement…
Q: Consider the given circuit, using the Kirchhoff's Law, find the value of V3 (in Volts) given the…
A:
Q: 2 4.
A: Since no external horizontal forces act on the set of four balls, so its centre of massstays fixed…
Q: For a 20 A, 230 V energy meter, the number of revolutions per KWh is 480. If upon test at full load,…
A: In this question we will find power consumed, energy consumed ....And error in measurement....
Q: EXAMPLE 18.4 For the network in Fig. 18.12, determine the sinu- soidal expression for the voltage u,…
A: given here a circuit and asked find the voltage V3 by usins the superposition theorem.
Q: Find the inductive reactance per mile of a single-phase line operating at 50 Hz. The conductor has a…
A:
Q: For main weinding, Vm = 23 V Im YA 60 w Vm Im (os Øm =60 60 23x4 (os Em =
A:
Q: 3. Determine the Resistance (R) to be added for the electrical circuit to supply maximum power…
A:
Q: Exercise (3-2): find Fourier series Question (1) f(x)=x/2 (2) f(x)=-x (3) f(x)=sinx (4) f(x)=coS x…
A:
Q: 7. The nameplate speed of a 60 hz induction motor is 1750 rpm. If the speed at no load is 1785 rpm,…
A:
Q: Design a MOD-10 Counter using a MOD-16 Counter.
A: The solution is given below
Q: Comparing electromagnetic relays to vacuum tubes, what were the advantages? What happened before…
A: Electromagnetic Relay: Electromagnetic relays are ones that use electromagnetic activity to work.…
Q: 7. A círcuit whose resistance is 20 ohms inductance of 10 H has a steady state voltage of 100 volts…
A:
Q: 7. A system operates at 220 kVA and 11 kV. Using these quantities as base values, find the base…
A: Since you have asked multiple questions in a single request, we will be answering only the 1st…
Q: 17.1 What are the keys to a successful mixed-signal PCB layout?
A: Types of PCB Single layer PCB Multi Layer PCB High frequency PCB Double layer PCB HDI layer PCB…
Q: I:? 12 レ、? 132
A:
Q: Find the ciosed loup thansfer function Y- B
A:
Q: Activity 5.1 1. On a 120/208-v four wire Y system, two lamps are connected from phase A to neutral,…
A: “Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: Ex.2: Design a synchronous cour MOD-6 , which follows the co sequence 000, 010, 011, 001, 100,…
A:
Q: Explain bus bar and bus bar chamber
A: In this question we will write about bus bar and bus bar chamber....
Q: ー2スV Io t RD 2.7k IRs = 7.5mA IDSS %3D Yp = 3.5V Ves RC Rs 1MA Z 1.
A: MOSFET is a metal oxide field effect transistor, it belongs to the family of FET, it is a…
Q: Design an optimized cascade buffer to drive a load capacitance of 5000C,. (a) What is the optimum…
A: Cascade Buffer: Cascade Buffer is used in 8259 PIC( Programmable Interrupt Controller)…
Q: 3. (a) Generate a system of equation by applying the node voltage law on the circuit below. (b)…
A: NODAL EQUATION: In electric circuit analysis nodal method is a method of determining voltage between…
Q: Question 2 5Ω 2F 12 3F Figure 2.1 Consider the system shown in figure 2.1 (a) (b) (c) (d) (e) Obtain…
A:
Q: A source follower has high input impedance, low output impedance, and a voltage gain less than one.…
A:
Q: Oraw The Complete Roo! locus k CS+5) GiS)Hi5)こ (2+5) (1+S) S
A: In this question we need to draw a root locus of the given system.
Q: The process transfer function between the input, m, and output, y, is given by, y(s) = 5 -m (s) 48 s…
A:
Q: Design a Programmable Logic Array (PLA) with 3 inputs and 3 outputs. The binary output is two…
A: The truth table can be obtained based on the given condition and the reduced Boolean expression can…
Q: Question 2 5Ω 2F 10 3F Figure 2.1 Consider the system shown in figure 2.1 (a) (h) Obtain the…
A:
Q: What are the rise time, fall time, and average prop- agation delay for a minimum size CMOS inverter…
A: It is given that:WLs=21WLp=21VDD=VH=2.5VCL=0.4pF
Q: 4) (a) What is the logic function implemented by the gate in Fig. P7.73? (b) Design the PMOS…
A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…
Q: Discrete Fourier Series 6.40 Find the DFS coefficients for the sequence ( 27Tn (n) = cos 10 27 n +…
A:
Q: If the base line-to-line voltage of a 3-phase system is 4kv and the base 3-phase MVA is 40 MVA, then…
A: We need to find out impedance for given details
Q: Question 03: A system has an open loop transfer function given by: G(S) = 50/(s(s+1)(s+5) Through…
A: The open-loop transfer function of the system is given as G(s)=50ss+1s+5 Phase margin is calculated…
Q: +lev ID = kn (VGs- Um)² %3D RD Ry Ž Kn = 0.1 MA/v? %3D UTh- av %3D RS 2ks Let RitRg= 100kn. Design…
A: In this question, We need to design the circuit if R1+R2= 100k ohm
Q: A circuit is constructed with four resistors, one inductor, one battery and a switch as shown. The…
A:
Q: A 50HZ, 440V, 6pole, delta connected three phase induction motor, running at full load develops a…
A:
Q: Compute for Aj . Vcc = 12V. %3D oVcc 4.7 k2 1 ΜΩ B= 90 To= 002 O 60.64 O 0.422 12902 O 89.8
A:
Q: 52 32 82 52 22 42
A:
Q: The Bode plot of unity feedback system is shwon in figure below O dB/dec +20 dB/dec -20 dB/dec -20…
A: In this question we will find unknown values of gain , a and b from given bode plot...
Q: 2. Applying Kirchhoff's rules, find the values of the current in each branch of the given circuit…
A:
Q: A UJT employed for the triggering of an SCR, stand-off ratio = 0.61 and DC source voltage and VBB is…
A:
Q: Q4: Consider th 2.5 volts. R2 is
A:
Q: . A 5-ohm load is connected to the secondary o! a 1100/110-v power transformer. The effective load…
A:
Q: 3. Determine the voltages 2A(t) 30. 0.9i 18 0
A:
Q: For main winding, Vm = 23 V Im P = 60 W Vm Im (os Øm >60 60 23x4 (os ¢m = (os Øm : 0.652 Øm = 49.29…
A: We need to find out angle for given power .
Q: P1. 16. Which of the following formulas can be used to determine the magnitude of a vector in an xy…
A: We need to select correct option for given statement
Step by step
Solved in 2 steps with 2 images
- Consider a family of logic gates that operate under the static discipline with the following voltage thresholds: VI=1.5V, VOL=0.5V, VIH=3.5V, and VOH=4.4V. a. What is the lowest voltage that can be output by an inverter for a logical 1 output? b. What is the highest voltage that must be interpreted by a receiver as logical 0? c. What is the lowest voltage that must be interpreted by a receiver as logical 1?(a) Differentiate comparatively the analogue and digital representations. (b) If 33210= Xs then find the value of X. (c)1001011.0112 to equivalent decimal (d) What do you know about the logic gates? Explain the AND gate in details. 410 AWe want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
- Draw a combinational logic circuit of a four input multiplexor where the inputs (X3;X2;X1;X0) are each one bit variables. Label the values of inputs and outputs of each gate of the circuit, assuming the four inputs have the values (X3;X2;X1;X0) = (1; 0; 0; 1) and assuming X1 is selected. [Do not draw the decoder circuit which is part of the multiplexer].Given the logic function: F(A,B,C,D) = Σm(0,4,5,10,11,13,14,15) a. Find a minimum circuit which implements F using AND and OR gates. Identify two 1-hazards in the circuit. b. find another minimum circuit which implements F using AND and OR gates. Identify two 0-hazards in the circuit. c. Find an AND-OR circuit for F which has no hazards.28)Which of the following elements does not affect how a ladder logic program is developed? A)The type, direct or inverse acting, and active state of the output field devices. B)The choice of normally-open and normally-closed instructions for the PLC program. C)The contact type and active state of the input field devices. D)The requirement for current sinking or sourcing inputs and outputs.
- Use Digital Logic Simulator Fill-in the blank boxes with the correct LOGIC GATE/ Full/Half Adderchoose the correct answer If a two-input logic gate produces a output of logic HIGH, only if both inputs are different, then the logic gate is? a. IC 7400 b. IC 7486 c. IC 7408 d. IC 7432draw the logic diagram using three basic 2-input logic gates F=(A'+C) (A'+ C') (A+B+C'D)
- There are 5 gates in a metrobus, 1 of which is to get on and 4 to get off. The number of passengers inside is desired to be seen on the LCD connected to the P2 port. Get-on gate is controlled by the P0.2 while get-off gates are controlled by the P0.3, P0.4, P0.5, and P0.6. The sensors generate Logic-1 while passing passengers. Since the passenger carrying capacity of the metrobus is 294, if the number of passengers exceeds the number of 294, the warning LED connected to the P0.7 pin is required to light up. Since other pins of P0 are used for other purposes, it is not desired to be changed. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?Draw the F1 and F2 outputs of the above logic circuit only with OR NOT gates and A, B, C, D independent logic variables in the Proteus program.Implement the following logic function using only 2 multiplexers 4 to 1. You can use Not and Or gates if necessary. f(A,B,C)=Π M (1,5,7)