Q12-Indicate whether the following statements are true or false and correct thefalse statements.1- A short circuit test of single phase transformer is done to determine the parametersof shunt branch of the equivalent circuit.2- The characteristic (angular speed versus T) of a dc shunt motor is known as theExternal characteristics.3- When a series d.c. motor is operate without load, the armature will not run4- The generation of electricity achieved by moving a conductor in a magneticfield due to the relation E= ILB5- In series d-c generator the field winding will be constructed from high number of turnsand high cross- sectional area of wire.6- Series motor maintains a more constant speed under varying load7-The armature voltage of d.c series generator is not affected by load current.8- In series d-c generator the field winding will be constructed from high number of turnsand high cross- sectional area of wire.9- If field resistance of a d.c. shunt generator is increased beyond its critical value, thegenerator output voltage will exceed its rated voltage10-The inter pole winding is connected in parallel to field winding

As per Guidelines we are supposed to do only First 3 Questions when multiple questions are given, so…

Q12-Indicate whether the following statements are true or false and correct the false statements. 1- A short circuit test of single phase transformer is done to determine the parameters of shunt branch of the equivalent circuit. 2- The characteristic (angular speed versus T) of a dc shunt motor is known as the External characteristics. 3- When a series d.c. motor is operate without load, the armature will not run

Q12-Indicate whether the following statements are true or false and correct the false statements. 1- A short circuit test of single phase transformer is done to determine the parameters of shunt branch of the equivalent circuit. 2- The characteristic (angular speed versus T) of a dc shunt motor is known as the External characteristics. 3- When a series d.c. motor is operate without load, the armature will not run

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A Y- connected, 10-KVA, 230- has a field winding resistance of 4.59. At an operation of 0.85 lagging power factor, the excitation current is recorded at 10A. the core loss is 300W, and the mechanical loss is 200W. If the corresponding efficiency is 84.9%. calculate the per- phase armature winding resistance.
A 2.3 kV, three phase, 50 Hz,SCIM gas a starting torque of 640 Nm, And starting current of 600 A. What will be the per unit tapping of auto transformer to reduce the starting Current from mains to 150 A Also find the corresponding starting torque.
A three phase, 4 pole, 3300 V, 50 Hz, star connected Induction motor, has identical primary and referred secondary impedance of value 3+j9 Ohm per phase. Using the approximate circuit, calculate: A. The full load torque at rated slip of 5%. B. The maximum torque at normal voltage and frequency.
A gas turbine, 2-pole, 3? synchronous generator rated at 200 MW is connected to the grid (presumed to be an infinite bus). The electrical operating frequency of the grid is 60 Hz, and the slope of the frequency-power curve for the generator is 15 MW/Hz. a. If the no-load setpoint for the generator is set to 63.5 Hz, how much active power will the generator provide to the grid? b. Neglecting system losses, what is the torque provided by the gas turbine? c. What would happen if the no-load setpoint for the generator is set to 59 Hz?
The rotor resistance and reactance of a squirrel-cage induction motor rotor atstandstill are 0.14 ohm per phase and 0.8 ohm per phase respectively. Assuminga transformer ratio of unity, from the eight-pole stator having a phase voltage of254 at 60 Hz to the rotor secondary, calculate the followingA. rotor starting current per phase.B. the value of slip producing maximum torque.
The armature of a 400V, 6-pole, 25 Hz single-phase series motor is lap-wounded with 504 conductors Motor field winding has effective resistance and leakage reactionance are 0.06 22 and 0.05 12, respectively and has 18 turns. However, the armature winding has a leakage reactance of 0.04 12 and negligible resistance. At rated motor current of 300A, the flux per pole is 0.05 Wb, the short circuit current is 50A and the equivalent current to iron losses is 40A. Find motor speed , torque and efficiency at rated current .
6. The major failure area of a typical wound-field and wound-armature DC motor isA. brush wear and failure.B. open field windings.C. a faulty commutator segment.
A four-pole, single-phase, 120 V, 60 Hz induction motor gave the following standstill impedances when tested at rated frequency:Main winding : Zm =1.5+j4 ohmsAuxiliary winding : Za =3+j6 ohmsa) Determine the value of external resistance to be inserted in series with the auxiliary winding to obtain maximum starting torque as a resistor split-phase motor.b) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque as a capacitor-start motor.c) Determine the value of the capacitor to be inserted in series with the auxiliary winding to obtain maximum starting torque per ampere of the starting current as a capacitor-start motor.d) Compare the starting torques and starting currents in parts (a), (b), and (c) expressed as per unit of the starting torque without any external element in the auxiliary circuit, when operated at 120V, 60Hz.
The primary leakage impedance and equivalent secondary impedance referred to stator atstandstill of a 3-phase, 220 V, 50-Hz, 4-pole induction motor are (0.4 + 3j)ohms and (1.2 + j1) ohms per phaserespectively. If the magnetizing current is neglected, determine the maximum torque the motor candevelop and slip at which it occurs.
A DC shunt generator has a full load output of 10kW at a terminal voltage of 240V. The armature and the shunt field winding resistances are 0.6 and 160 ohms respectively. The sum of the mechanical and core-losses is 500W. calculate the power required in kW at the driving shaft at full-load, and the corresponding efficiency and voltage regulation
A 25-horsepower, 230V, 60Hz, 3-phase induction motor has a Nameplate Rating of 58amperes. The nameplate also shows a temperature rise of 30°C. a) Determine the THHN Cable and TW grounding conductors.b) Conduit Size using EMTc) What is the overload size for this motor?d) Determine the locked rotor current if the motor is Code J.e) Determine the Dual-element, time-delay fuses to be used for the motor’s branch circuit.
A shunt generator has a field resistance of 60 ohms. When the generator driven 6KW, the terminal vtage is 125 Volts, while the generated emf is 133V. Determine a.) The armature resistance, and b.) The generated emf when the output is 2KW at terminal voltage of 135 V.