Q12. At a depth of 9 km in the ocean the strain is 90MN / (m ^ 2) The precise weight of the ocean water on the floor is 10 * 2kN/(m ^ three) and its average bulk modulus is two * 4 * 10 ^ 6 * kN / (m^2) determine (a) the trade in precise extent, (b) the particular extent, and (c) the particular weight of sea water at 9 km intensity.

Q12. At a depth of 9 km in the ocean the strain is 90MN / (m ^ 2) The precise weight of the ocean water on the floor is 10 * 2kN/(m ^ three) and its average bulk modulus is two * 4 * 10 ^ 6 * kN / (m^2) determine (a) the trade in precise extent, (b) the particular extent, and (c) the particular weight of sea water at 9 km intensity.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The extruded plastic shape will be subjected to an internal shear force of V = 280 lb. Dimensions of the cross section are b = 1.1 in., d = 2.2 in., c = 1.5 in., and t = 0.20 in. Determine:(a) the magnitude of the horizontal shear stress at points A and B.(b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 0.8 in. below the z centroidal axis.(c) the magnitude of the maximum horizontal shear stress in the extrusion.
The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of the cross section are b = 2.0 in., D = 4.0 in., C = 2.7 in., And t = 0.19 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 1.4 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion
A cantilever beam 80 mm wide by 260 mm high and 9 m long carries a lpad that varies uniformly from zero at the free end to 1200 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 4 m from the free end. Answers must be in MPa.
Q) If the failure of shearing stress in a steel plate is 2,300KN, determine (a) the force required to punch a 32 mm diameter hole in a 10mm thick plate and, (b) the corresponding normal stress ina punch. Solve it early
Q) If the failure of shearing stress in a steel plate is 2,300KN, determine (a) the force required to punch a 32 mm diameter hole in a 10mm thick plate and, (b) the corresponding normal stress ina punch.
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
A hollow circular bar having outside diameter twice the inside diameter is used as a beam. From BMD of the beam, it is found that the bar is subjected to a maximum bending moment of 40 kN-m. If the allowable bending stress in the beam is to be limited to 100 MN/m?, find the inside diameter of the bar.
Two horizontal plates are parallel to one another and separated by an oil film (SAE 10 oil at 20 deg C, Table A.4) that is 1.0 mm thick. The upper plate moves to the right at 2.0 m/s. The bottom plate moves to the right at 6.0 m/s. What is the shear stress in N/m2 of the oil on the upper plate? Is the shear stress on the upper plate directed to the right or to the left?
A large uniform cylindrical steel rod of density ρ = 8.8 g/cm3 is 4.0 m long and has a diameter of 5.0 cm. The rod is fastened to a concrete floor with its long axis vertical. What is the normal stress in the rod at the cross section located at (a) 2.0 m from its lower end? (b) 2.5m from the lower end? Your answer
STRENGTH OF MATERIALS: Answer should be 6.17 cm A beam rests on supports 3 m apart carries a load of 10 kN uniformly distributed. The beam is rectangular in section 7.5 cm deep. How wide should it be if the skin-stress must not exceed 60 MN/m^2?
The extruded plastic shape has dimensions of D = 21 mm. d = 17 mm. a = 87 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 360 N. (b) If the allowable shear stress for the plastic material is 1050 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
Stress=100MN/m Area=bh b=0.5m h=? Determine the stress in members BC, CD and CE A= bh