Q1:360 liters per second of water is flowing in a pipe. The pipe is bent by 120°. The pipe bend measures 360 mm x 240 mm and volume of the bend is 0.14 m3. The pressure at the entrance is 73 kN/m² and the exit is 2.4 m above the entrance section. Find the force exerted on the bend. Y→ P -100 (~) 240 min dia Y 360mm 240 mm

Q1:360 liters per second of water is flowing in a pipe. The pipe is bent by 120°. The pipe bend measures 360 mm x 240 mm and volume of the bend is 0.14 m3. The pressure at the entrance is 73 kN/m² and the exit is 2.4 m above the entrance section. Find the force exerted on the bend. Y→ P -100 (~) 240 min dia Y 360mm 240 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe has an initial radius of r1, which then changes to a radius of r2. The velocity of the water in the initial part of the pipe is v1. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? let r1=10cm let r2=6cm let v1=5m/s b) What is the volume flow rate in the pipe?
The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground. A. 13.5 psi B. 14.4 psi C. 16.5 psi D. 15.5 psi With F.B.D.
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m
An industrial fan delivers 55,000 CFM of air through a discharge duct with a size of 3 ft x 4 ft where the static pressure is 6-inch water gage. At the inlet, the duct diameter is 4 ft and the static pressure is 1-inch water gage. The temperature of the air is 78 F and barometric pressure is 14 psia. (ρw = 62.2 lb/ft³). Determine: a). the total pressure in feet of air b). the static power in HP c). the fan power in HP
Include a free body diagram A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. -4.67 m C. 2.56 D. -2.72 m
14. Through a refinery, fuel ethanol is flowing in a pipe at a velocity of 1 m/s and a pressure of 101300 Pa. The refinery needs the ethanol to be at a pressure of 2 atm (202600 Pa) on a lower level. How far must the pipe drop in height in order to achieve this pressure? Assume the velocity does not change. (Hint: Use the Bernoulli equation. The density of ethanol is 789 kg/m3 and gravity g is 9.8 m/s2
please include fbd A 22 L kerosene tank is filled with 2 cm diameter hose equipped with a 1.5 cm nozzle meter If it takes 20 s to fill the tank, determine the pressure differnce indicated by the nozzle if Cd= 0.96. The specific gravity of kerosene is 0.82. a. 12.8 kPa b. 11.8 kPa c. 10.8 kPa d. 9.8 kPa
The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank at the ground level and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, but the pressure over the water surface is unkown. Determine the minimum tank air pressure (gage) that will cause a water stream from the nozzle to rise 72 ft from the ground. (WITH FREE BODY DIAGRAM) CHOICES: A.16.5 psi B.15.5 psi C.13.5 psi D.14.4 psi
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
An orifice of diameter 150 mm is fitted at the bottom of a boiler drum lenth 6 m and of diameter 2 m. The drum is horizontal and contains water up to height of 1.8 m. Find the time required to empty the boiler. Take Cd=o 0.60. a.127 seconds b.467 seconds c.175 seconds d.217 seconds
Assume 4 kg/s of fluid are moving through an insulated pipe under these conditions: v1 = 6 m/s and u1 = 40 J/kg. (a) Find E1, in W (whole number) . (b) If the fluid flows through an upward bend of the pipe until v2 = 2 m/s and u2 = 45 J/kg, through what vertical height did the fluid travel? (2 decimal places) Local g = 9.75 m/s2.
Water of density ? =998.2kg/m3 flows through a fireman’s nozzle—a converging section of pipe that accelerates the flow. The inlet diameter is d1 = 0.100 m, and the outlet diameter is d2 = 0.050 m. The average velocity, momentum flux correction factor, and gage pressure are known at the inlet (1) and outlet (2). (a) Write an expression for the horizontal force Fx of the fluid on the walls of the nozzle in terms of the given variables. (b) Verify your expression by plugging in the following values: ?1 = 1.03, ?2 = 1.02, V1 = 3 m/s, P1,gage = 137,000 Pa, and P2,gage = 0 Pa.