Q2) 25-mm diameter shaft is pulled through a cylindrical bearing as shown in Fig.2. The lubricant that fills the 0.3-mm gap between the shaft and bearing is oil having a kinematic viscosity (0.0008 m²/s) and a specific gravity of 0.91.Determine the force P required pulling the shaft at a velocity of 3m/s.

Q2) 25-mm diameter shaft is pulled through a cylindrical bearing as shown in Fig.2. The lubricant that fills the 0.3-mm gap between the shaft and bearing is oil having a kinematic viscosity (0.0008 m²/s) and a specific gravity of 0.91.Determine the force P required pulling the shaft at a velocity of 3m/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To determine the shear stress of oil, two horizontal plates are placed 15 cm apart, the space between them is filled with the oil of viscosity 15 poise. If the upper plate is moving with velocity 2,000 mm/s, find the shear stress (τ).
The space between two square flat parallel plates is filled with oil. Each side of the plate is 0.9 m. The specific weight of the oil is 9780 N/m3. The thickness of the oil film is 12.7 mm and requires a force of 170 N. The liquid having the kinematic viscosity of 18.5 stokes. Determine (i) the shear stress (ii) the density of oil (iii) the dynamic viscosity in poise and (iv) the moving velocity of the upper plate
A skater weighing 500 N skates at 10 m/s and is supported by an average skating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of thin film of water existing between the skates and the ice. Follow the methodologies in solving the problem; Given : Required: Schematic Diagram: Solution:
The space between two square parallel flat plates is filled with oil.each side of the plate is 720mm. The thickness of the oil film is 15mm. The upper plate which moves at 3m/s requires a force of 120N to maintain the speed. Determine the dynamic viscosity and kinematic viscosity if specific gravity of oil is 0.95
Two plates are placed at a distance of 15 mm apart. The lower plate is fixed while the upper plate having surface area of 1.0 m^2 is pulled at 0.30 m/s. Whar is the force in Newton required to the speed if the fluid separating them is having viscosity of 1.5 poise?
Determine the force required to drag a thin plate placed in themiddle of two parallel plates 24 mm apart with the space filledwith a fluid of viscosity 0.82 Ns/m2. The area of the plate is 0.5 m2and the speed at which it is dragged is 0.6 m/s. Also find the force ifthe thin plate is at 8 mm from one of the plates.
Plunger having diameter of 10 inch slides in a 10.006 inch diameter of a cylinder, the annular space being filled with oil having a viscosity 0.004 ft²/s and (S.G=0.85). If the plunger moves with a velocity of 0.6 ft/s. What is the resistance when 9ft inside the cylinder.
If the viscosity of water at 70 °C is 0.0042 poise and its specific gravity is 0.97, determine its kinetic viscosity in centistokes.
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
The space between two square flat parallel plates is filled with oil. Each side of the plate is 720 mm. The thickness of the oil film is 15 mm. The upper plate, which moves at 3 m/s requires a force of 120 N to maintain the speed. Determine: (i) The dynamic viscosity of the oil; (ii) The kinematic viscosity of oil if the specific gravity of oil is 0.95.
If a force (p) of ( 7.8 ) N causes the 30 mm diameter shaft to slide along the lubricated bearing with a constant speed (y) of 1.4 m/s, determine the hydraulic shear stress (T) and dynamic viscosity ( Mu ) of the lubricant .Also , find the constant speed Ynew in m/s of the shaft when the magnititude of P is tripled value .The gap between the bearing and the shaft is1 mm and the width of the shaft (x) is 23 mm as shown in the figure bellow. 1.The hydraulic shear stress ( Tau) is------- The answer in kPa? 2. The value of the dynamic viscosity ( Mu ) in Pa.sec is? 3. The new speed of the shaft when the value of the force P has been tripled is The answer in m/sec?
If a force (p) of ( 0.9 ) N causes the 30 mm diameter shaft to slide along the lubricated bearing with a constant speed (y) of 1.8 m/s, determine the hydraulic shear stress (T) and dynamic viscosity ( Mu ) of the lubricant .Also , find the constant speed Ynew in m/s of the shaft when the magnititude of P is tripled value .The gap between the bearing and the shaft is1 mm and the width of the shaft (x) is 20 mm as shown in the figure bellow. The hydraulic shear stress ( Tau) is------- In pa? The value of the dynamic viscosity ( Mu ) in Pa.sec is? In pa.sec The new speed of the shaft when the value of the force P has been tripled is? In m/sec