Q2) A building wall consists of 12-in. clay brick and --in. fiberboard on one side. If the wall is 10 ft high, determine the load in pounds per foot that it exerts on the floor. Q3) A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, determine the load in kN/m that it exerts on the floor.

Q2) A building wall consists of 12-in. clay brick and --in. fiberboard on one side. If the wall is 10 ft high, determine the load in pounds per foot that it exerts on the floor. Q3) A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, determine the load in kN/m that it exerts on the floor.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.65P: Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero,...

See similar textbooks

Similar questions

A horizontal cable exerts a force of 399.971 pounds while holding a boom into place. Determine the angle the boom makes with the ground if it supports a 1000-pound load, as shown in the figure. Include fbd, given and solution.
A load of P = 4900 N is acting on member AC. The length of AC is d = 300 mm. The cross-sectional area of AB is 375 mm2 while the cross-sectional area of C is 575 mm2 . Determine the magnitude (in N) of the force acting on rod AB if the compressive stress in the smooth support C is equal to the tensile stress in the rod AB. Round off the final answer to two decimal places.
In this figure is a strut and a cable which was use to lift a body. If the strut and a cable has a stress equivalent to your 50 and 76 in kips respectively determine the maximum weight of the body. Neglect the weight of the wood and cable. Round off the answer in two decimal places.
A 50 kg fisherman sits at the center of the boat rented in a private resort, which has a uniform width and a weight per linear foot of32 lb/ft, that will be used for island hoping in the area. The boat is 3 m long. Assume that the water exerts a uniform distributed load upward on the bottom of the boat. a) What is the applied load (lb) applied to the boat due to the weight of the fisherman? Round up to the next whole value. b) Using the applied load at Item a, what is the maximum shear force (lb) exerted on the boat?
Question 2 A pulley-load system is used to open and close the gate AB as shown. The gate is 5 m long and 2.5 m wide and has a mass of 4.7 tons. The load is a cube made of concrete with density of 2400 kg/m. a) Determine the minimum volume of the cubic load that is required to hold the gate in this closed position. b) Suggest a simple modification that can be done in the system in order to further reduce the minimum volume of the cubic load required for keeping the gate in closed position.
Two men are carrying on their shoulders a 500-N load suspended from a piece of bamboo 3 m long with each man positioned at the ends. If the load is suspended 1 m from one end find the load carried by each.
A beam of length L = 22 in supports a load which varies from w = 20 lb per ft at the right end to zero at the left end. Determine the position (in meters) of the resultant load measured from the left.
A crane is supported by two cables with a cross-sectional area of 3.04 cm2 each. Determine the amount of stress on each cable.
Abbot and Costello are transporting a 0.125m3 cubic block along a ramp inclined at 20°. They tied the block under the midpoint of a 3m, 2kg, pole-arm. Abbot is at the lower end of the pole while Costello leads the pair up, holding the other end of the pole. Calculate the upward forces exerted by Abbot and Costello during the transport if the block weighs 1000N.
The barrier shown is commonly used during Highway Determine the weight per foot of length if it is made from plain stone concrete having a unit weight of 144 lb/ft3
Find the tension of AB, BC, and BD in pounds.
Q2- Use the method of sections to determine the force in member CE. 40KN BOKN 40kN