Q2) A parallel plate is moving over another plate as shown in the figure below. The liquid viscosity is 5x10°m²/s and its specific gravity is 0.88. Assuming linear velocity distribution in the gap please calculate the power required to pull the upper plate. Please show the directions of the shear stress at the lower and upper plates separately. U = 0.3 m/s d = 0.3 mm

Q2) A parallel plate is moving over another plate as shown in the figure below. The liquid viscosity is 5x10°m²/s and its specific gravity is 0.88. Assuming linear velocity distribution in the gap please calculate the power required to pull the upper plate. Please show the directions of the shear stress at the lower and upper plates separately. U = 0.3 m/s d = 0.3 mm

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Find the expressions to calculate the maximum normal and shear stresses for a circular profile: d (diameter)= 0.30 m
Determine the magnitude and location of the resultant hydrostatic forceacting on the submerged rectangular plate AB shown.The plate has a width of 1.5 m; ρw = 1000 kg/m3.
A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 76 kN and torques TB = 15 kN-m and TC = 4 kN-m, which act in the directions shown. Determine the normal stress x at point H.
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the resultant hydrostatic force on one side of the plate.
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm
Consider a beam having an I-type cross section as shown in figure. A shearing force V of 150 kN acts over the section. Determine the maximum and minimum values of the shearing stress in the vertical web of the section.
The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m) a) Show the support reactions and load occurring on the rod. b) Do you calculate support reactions? c) Calculate the Normal Force, Shear Force and Moment values by cutting from the points you have determined. d) Draw cross-section impact diagrams? Do you specify the maximum positive and negative moment values? e) Check the cross-sectional influence diagrams with a simple method, briefly explain the control steps.
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. Wherein: Q=2 T=6 Example: 2QT kN = 226 kN T.Q5 m = 4.25 m
H1. A rectangular beam of 100mm wide and 150mm deep is subjected to Shear force of 30KN, Determine ratio of Maximum shear stress to Average shear stress. Derive the equation which is used to find out the shear stress.
If a twisting moment of 1100 N-m is impressed upon a 4.4 cm ø shaft;1. What is the maximum shearing stress (in MPa) developed? 2. What is the angle of twist (in rad) in a 150 cm length of the shaft?Gsteel = 85 GPa.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft.