Q2: A sinusoidal signal v(t) system. The equalizer is of a midrise type, with a step size of 2 volt. = 10 Cos( 2 nt) is transmitted using a 5-bit binary PCM 1. Sketch the quantizer curve ( input-output ) 2. Sketch the PCM wave for one complete cycle of the input, assume a sampling rate of four samples per second, with samples taken at t = 3. Determine code words at the time instants t =±1/8, ±2/8, +3/8, +4/8 4. Determine the minimum step size for delta modulation of the sinusoidal signal

Q2: A sinusoidal signal v(t) system. The equalizer is of a midrise type, with a step size of 2 volt. = 10 Cos( 2 nt) is transmitted using a 5-bit binary PCM 1. Sketch the quantizer curve ( input-output ) 2. Sketch the PCM wave for one complete cycle of the input, assume a sampling rate of four samples per second, with samples taken at t = 3. Determine code words at the time instants t =±1/8, ±2/8, +3/8, +4/8 4. Determine the minimum step size for delta modulation of the sinusoidal signal

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

kindly explain this part ,, how sinc100t is represemted in frequency domain
Find the figure of merit for an AM receiver, where the amplitude sensitivity, ka, is V0.5 Volts, and average power, P, is 1 W. For this system, calculate the required channel SNR for an output SNR of 20 dB.
During a vibration measurement experiment in the Mechanical Engineering Department at Hacettepe University, a piezoelectric accelerometer output is given by this mathemtaical equation: a (t) = 1 + 4 sin(43.98t) + 7sin(100.53t) in gravity acceleration (g) value. a) Determine the frequencies (in Hz) contained in the signal. Round your results to nearest integer value. b) What is the minimum sampling rate to avoid aliasing? c) Sketch clearly the frequency spectrum if the signal is sampled at 15 Hz. d) Now, the signal is filtered with a low-pass Butterworth filter to remove the maximum frequency component. It is desired to attenuate the amplitude of this component to at least 5 % of its value. If the sampling rate is now 20 Hz, what will be the order of the filter? e) If the blue one is our signal, then what is red and green ones? Write down the mathematical relation between the three signals? (Use labels as blue, red and green signal.)
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 650 kHz is amplitude-modulated by a 2 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 140Vp and 60Vp respectively. The equivalent resistance of the transmitting antenna is 30 Ω. Determine: ( i ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC.
1. We use the DFT to compute the amplitude spectrum of a sampled data sequence with a sampling rate fs =2,000Hz. It requires the frequency resolution to be less than 0.5 Hz. determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.
You have an FSK transmitter using a mark frequency of 500 kHz, a space frequency of 380 kHz, and sending 10 kbps. A) How much bandwidth do you need for your transmission? B) if you are to design the system with continuous phase shift keying in mind, what would be the value of the space frequency if the mark frequency remains the same?
A digital communication link carries binary-coded words representing samples of an input signal, xa(t)=3cos⁡(600πt)+2cos⁡(1800πt)The link is operated at 1,000 samples/s. (a) What is the folding frequency? (b) What is the Nyquist rate for the signal xa(t)? (c) What are the frequencies in the resulting discrete-time signal x(n)? (d) Will there be any aliasing here? (e) Which frequency will alias to what frequency
Q 2 :J An audio signal given by 15sin(4000pi * t) + 20sin(8000pi * t) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60sin(100, 000pi * t) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why? to
Plot an AM modulated signal , that has an information signal m ( t ) = 10 sin ( 10nt ) and a carrier signal c ( t ) = 15 cos ( 1000nt ) . Calculate the modulation index ( u ) . Is it a good modulation ? If no , suggest a change in one of the signals above and calculate u again , so that it approaches ideal case
Message sign; m (t) = 10sinc (400 * t), and carrier sign; c (t) = 100cos (2 * pi * f * t) modulates by phase modulation. Modulation index 6, message bandwidth W = 200 Hz. • Obtain the mathematical expression of the phase modulated sign, u (t). • What is the maximum phase deviation of the modulated signal? • What is the strength of the modulated signal?
A subcarrier given in Eq. 4.1 is amplitude modulated by an information signal given in Eq. 4.2. The resulting AM signal is then used to amplitude modulate the signal given in Eq. 4.3 to generate a signal that is finally transmitted. Derive a mathematical expression for this final signal that is transmitted. How, in practice, can this system be made with minimum harmonic distortion? Equations for Question 04
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 750 kHz is amplitude-modulated by a 4 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 180Vp and 70Vp respectively. The equivalent resistance of the transmitting antenna is 60 Ω. Determine: (i) The peak amplitudes of the audio, carrier sideband voltages and modulation index. (ii) Using the above results, write the complete AM mathematical representation to express the waveform, showing its carrier, lower sideband and upper sideband parameters. (iii) The power of the carrier signal, total sidebands power and the bandwidth of the modulated signal. Then sketch and label the power spectrum of the modulated ( i v ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC