Q2: A/ The full-wave controlled bridge rectifier of has an ac input of 200 V peak to peak at 50 Hz and 7 ohm load resistor. The delay angle is 45 degree. Determine the average current in the load, the power absorbed by the load, and the source volt amperes, draw the circuit

Q2: A/ The full-wave controlled bridge rectifier of has an ac input of 200 V peak to peak at 50 Hz and 7 ohm load resistor. The delay angle is 45 degree. Determine the average current in the load, the power absorbed by the load, and the source volt amperes, draw the circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous
A single-phase fully controlled, full-wave, bridge rectifier has a source of 230 V rms at 50 Hz, and is feeding a load R = 25 and L = 10 mH. The firing angle α = 45˚ and the current extinction angle β =230˚. It is required to: (a) Sketch the appropriate load voltage and load current waveforms. (b) Determine whether the current is continuous or discontinuous. (d) Determine the average load voltage and current. (e) Determine the rms load voltage and current. (f) Determine the a.c. and d.c powers absorbed by the load. (g) Determine the efficiency of the converter.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
The voltage waveforms shown below are obtained from a three-phase power rectifier used in an ESKOM application.The rectifier output before the inductive filter is denoted by VL and the load voltage after the inductive filter by Vo. Ignore any diode losses and consider a load resistance of 12.7 Ω. Analyse the waveforms and specify / calculate,11) the supply frequency;12) the rectifier pulse number;13) the rectifier average output voltage;14) the average output current;15) the r.m.s. value of the output current;16) the r.m.s. value of the harmonics present in the output current;17) the dc current rating of the rectifier diodes;18) the r.m.s. current rating of the rectifier diodes;19) the peak repetitive reverse voltage rating of the rectifier diodes;20) the peak repetitive forward current rating of the rectifier diodes;21) the line-line r.m.s. voltage of the three-phase supply;22) the rectification efficiency of the converter;23) the converter transformer utilisation factor;
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz. The firing angle α = 45˚ and the current extinction angle β =255˚; (i) Determine whether the current is continuous or discontinuous and write the condition. (ii) Sketch the appropriate load voltage and load current waveform. (iii) If the firing angle is increased into 110˚, state the polarity of voltage and power for that condition.
For the Zener regulated power supply a shown, the rms value of vI is 15V, the operating frequency is 60Hz, R =100Ω, C =1000μF, the on voltage of diodes D1 and D2 is 0.75V, and the Zener voltage of diode D3 is 15V.(a)What type of rectiﬁer is used in this power supply circuit?(b) What is the dc voltage at V1? (c) What is the dc output voltage VO?(d)What is the magnitude of the ripple voltage at V1? (e) What is the minimum PIV rating for the rectiﬁer diodes? (f) Draw a new version of the circuit that will produce an output voltage of−15 V.
Figure shows an AC source G having an effective voltage of 240 V, 60 Hz is connected to a single-phase full-wave rectifier. The resistance for R is 53 Ω and ripple-to-ripple current is 15%.Determine the DC voltage and DC current across the resistor. Hence, determine the power absorbed by the load. Assuming all diodes are ideal.
A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage source of 380V, 50 Hz. The load is resistive with R=15 2. Calculate: (a) The average output voltage and average load current of the rectifier. (b) The d.c. and a.c. power dissipations in the load. (c) The diode ratings. (d) What is the lowest ripple frequency of the output voltage waveform?
1. A single-phase, 120V, 50Hz supply is connected to a controlled half-wave thyristor rectifier and series R-L load consisting of a resistor R of 350 ohms and inductor L of 150mH. The thyristor firing angle is 65 degrees. Assume the diode and thyristor are ideal. i) calculate the dc load voltage VDC and the load dc current IDC. ii) briefly explain why a freewheeling diode is often connected in parallel to an R-L connected load in rectifier circuits
A number of diodes rated at 1620 V each are to be connected in series in a rectifier circuit with a maximum voltage of 3000V. A de-rating factor of 15% is recommended. The maximum difference in leakage current of the diodes is given as 10mA , and the maximum difference in stored charge is 20µC. Calculate, 1) the number of diodes that must be used, 2) a suitable component value for the static equalization circuit; 3) a suitable component value for the dynamic equalization circuit.
A single-phase full-wave rectifier uses a power transformer whose secondary voltage is 220V r.m.s. The load resistor is 100kΩ. Neglect the transformer losses and the forward drops in the diodes. Determine the following: DC output voltage 2. Ripple voltage