Q2-A- Use the graphical method to find the magnitude and direction of the resultant of these forces Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a body is zero, the body is said to be in (a) rotating condition (b) translation condition (c) equilibrium condition 2. Number of component of reaction at hinge support are (a) zero (b) one (c) two (d) three 3. The angle that the vector A=2i+3j makes with y-axis is 4. If angle made by the force with y and z axes are 0,= 60° and 9, = 45° then 0₂ = 5. Force is completely defined by its (a) magnitude (b) direction (c) point of application (d) All of these F-700 N *90 F₂ - 500 N (d) dynamic condition

Q2-A- Use the graphical method to find the magnitude and direction of the resultant of these forces Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a body is zero, the body is said to be in (a) rotating condition (b) translation condition (c) equilibrium condition 2. Number of component of reaction at hinge support are (a) zero (b) one (c) two (d) three 3. The angle that the vector A=2i+3j makes with y-axis is 4. If angle made by the force with y and z axes are 0,= 60° and 9, = 45° then 0₂ = 5. Force is completely defined by its (a) magnitude (b) direction (c) point of application (d) All of these F-700 N *90 F₂ - 500 N (d) dynamic condition

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.155P: Assuming that P=48000lb and that it may be applied at any joint on the line FJ, determine the...

See similar textbooks

Similar questions

Draw the FBDs for the beam ABC and the segments AB and BC. Note that the two segments are joined by a pin at B. Count the total number of unknowns and the total number of independent equilibrium equations.
Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero, compute (a) the maximum tensile force in the cable; and (b) the length of the cable.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The horizontal boom carries the weight W=108lb at A. The boom is supported by the cables AB and AC. The tensions in the cables are TAB=120lb and TAC=160lb. Determine the single force R that is equivalent to three forces acting on the boom at A.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Determine the ratio P/Q of the forces that are required to maintain equilibrium of the mechanism for an arbitrary angle . Neglect the weight of the mechanism.
Assuming that P=48000lb and that it may be applied at any joint on the line FJ, determine the location of P that would cause (a) maximum tension in member HI; (b) maximum compression in member CI; and (c) maximum tension in member CI. Also determine the magnitude of the indicated force in each case.
A system of three pin connected bars takes the depicted equilibrium position under the given loading with the forces F1 and F2. What is the ratio of F1/F2?
A force of P=280 N is applied on semicircular rod at point B. Determine internal forces at point J if θ=30°. (draw free body diagram)
A 30 kg barrel is sitting on a handcart as shown below. Determine the normal forces at A and B. Please show all work and drawl FBD
Determine the Angles ʆ and θ so that the forces shown will be in equilibrium. Use equilibrium formula in the computation.