Q2) At a point in a structuresubjected to plane stress, thestresses are shown in Fig. 2a. Astress element located at the samepoint in the structure (but orientedat a eousterclockwise angle ß withrespect to the x axis) is subjectedto the stresses shown in the Fig.2b:o =?, o, = -15 ksi, txy5 ksi ).yOy=?o= 15 ksi5 ksi%3D%3D(a)(b)Using Mohr's circle, find: oy.o,and B

Answered: Image /qna-images/answer/1606a26c-961d-4fce-b4de-d4afc4bd3918.jpg

Q2) At a point in a structure subjected to plane stress, the stresses are shown in Fig. 2a. A stress element located at the same point in the structure (but oriented at a cousterclockwise angle ß with respect to the x axis) is subjected to the stresses shown in the Fig.2b: o =?, o, = -15 ksi, txy= 5 ksi ). Using Mohr's circle, find: oy, o, and B dy=? 6= 15 kst 5 ksi %3D %3D (a) (b)

Q2) At a point in a structure subjected to plane stress, the stresses are shown in Fig. 2a. A stress element located at the same point in the structure (but oriented at a cousterclockwise angle ß with respect to the x axis) is subjected to the stresses shown in the Fig.2b: o =?, o, = -15 ksi, txy= 5 ksi ). Using Mohr's circle, find: oy, o, and B dy=? 6= 15 kst 5 ksi %3D %3D (a) (b)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter13: Method Of Consistent Deformations Force Method

Section: Chapter Questions

Problem 60P

See similar textbooks

Similar questions

The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods wereinitially stress-free, what is the largest load P that can be applied without exceeding stresses of 182 MPa in the steel rod and 60 MPa in the bronze rod? D = 0
Determine the reactions and draw the shear and bending moment diagrams for the beam shown in Fig. 13.3(a) by the method of consistent deformations.
(a) A steel structural member of length = 10 ft. is supported between two fixed supports so that it cannot expand. At 68°F, there is no stress in the member. (E = 30 x 106 psi and α = 6.5 x 10-6/°F) Calculate the stress (psi) in the member at 95°F. Stress (psi) = (b) If the same structural member is not supported between two fixed supports, calculate the total elongation of the member (in.) for the same temperature change. elongation (in.) =
Q4: For the structure shown in Fig.4, determine the force supported by members BD, DE and CE. +J kN ‘(I kN 2m—l—2m——2 |||—-l—- Fig.4
Compute the deformation in member 1 which is solid alumnim with a area of 214159 mm^2
A steel strut S serving as a brace for a boat hoist transmits a compressive force P = 63 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 8 mm and the angle θ between the strut and the horizontal is 41°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 19 mm, the thickness of the gussets is tG = 14 mm, the thickness of the base plate is tB = 10 mm, and the diameter of the anchor bolts is dbolt = 10 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa.
Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 20 ft and b = 15 ft. Joint C is given a horizontal displacement of 5.2 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement?
For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm2 and Young’s modulus E = 200 GPa. Let P = 90.9 kN. a) Strain energy for truss AC. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. b) Strain energy for truss AB. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. c) Strain energy for truss BC. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. d) Strain energy for truss BD. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. e) Strain energy for truss DC. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. f) Strain energy for truss DF. Enter your answer in J to 2 decimal places. Positive value indicates tension, negative value compression. g) Strain energy for truss FC. Enter…
The cracked moment, Mcr of the beam shown in Fig.(5), is
1. The location of the centroid measured from the top fiber in (mm) 2. The moment of inertia about the centroidal x axis (mm) 3. The maximum compressive stress in (MPa) 4. The maximum tensile stress in (MPa) 5. The maximum shear stress at junction between the web and the flange (within the web) (MPa) 6. The maximum shear stress at the neutral axis in (MPa)
Determine the reactions and the force in each member of the truss shown in Fig. 13.6(a) using the method of consistent deformations.
a) List four different methods that could be used to determine the reactions for the statically indeterminate beam shown in Figure 4. b) Using the method of consistent deformations, calculate the support reactions and draw shear force and bending moment diagrams for the beam shown in Figure 4. Note that CD kN = 8kN