Please answer ASAP thank you and God Bless PROBLEM 05: A pipe AB carries water and tapers uniformly from a diameter of10cm at A to 12cm at B over a length of 2 m. Pressure gauges are installed at A,B and also at C, the midpoint of AB. If the pipe centerline slopes upwards fromA to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3bar, respectively. (1 bar = 100 kPa). Illustrate the problem and show yourcomplete solution.(a) Determine the flow, in m^3/s through the pipe at C neglecting alllosses. (1 bar = 100 kPa). *Your answer(b) Determine the pressure in bars, recorded at C neglecting all losses.Your answer

given- a tapered pipe carrying water. required-to determine flow and pressure at C.

Answered: (a) Determine the flow, in m^3/s…

(a) Determine the flow, in m^3/s through the pipe at C neglecting all losses. (1 bar = 100 kPa). * Your answer (b) Determine the pressure in bars, recorded at C neglecting all losses.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the pressure (in kN/m2) in the pipe shown (Pressure A) if y=1.24 m, h=1.02 m, and the manometry fluid is mercury (Specific Gravity=13.6).
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
In a pipe 300 mm in diameter, water flows over a length of 300 m, connecting point A, at topographic elevation of 100.0 m, in which the internal pressure is 291 kPa, to point B, at topographic elevation 74 .0 m, where the internal pressure is 334 kPa. Determine the direction of flow. Data: Specific gravity of water = 10 kN/m3. A) from B to A B) There is no drain. 0 C). from A to B For the previous question, calculate the pressure drop between A and B, in meters. ( ) If the flow is equal to 0.18 m3/s, calculate the friction factor of the pipe. ( ) For this same flow rate, calculate the friction velocity. ( )
1. The figure shows a looping water pipe system. Pressure at A = 85 m and E = 55m. Assume f = 0.053 all pipes. a. Compute the discharge at pipe 1b. Compute the discharge at pipe 2c. Compute the discharge at point B
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
Water flows from A to E through the pipe system shown. It is known that the flow in pipe BFGC IS 30 LITERS /SEC. and that the pressure head at A is 60 m. Assuming that f =0.022 and that all the pipes are level, determine the total flow from A to E and the pressure heads at B, C, D and E.
Orifice meter with orifice cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauges fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of discharge using Cd=0.6.
The pressure gauges are inserted at A and B in a vertical pipe converging water. The diameters at A and B are 150mm and 75mm respectively. The point B is 2.3m below point A. When rate of flow down the pipe is 0.021m³/s. The pressure at B is 117.72 KN/m² greater than at A. The losses in pipe between A and B are expressed as(KVa²/2g) where Va is velocity of A. Find the value of K. If the pressure gauges at A and B are replaced by tubes filled with water and connectef to a u-tube containing Hg(SHg=13.6) calculate the value of the reading manometer.
Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses (b) Working from Bernoulli's equation, determine the difference in levels (in mm) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil Draw illustrations Use 3 decimals
Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 896.61 L/min from the reservoir and through the pipe shown in the Fig. below. Compute the pressure at point B, considering the energy loss due to friction, but neglecting other losses. Also, use pipe roughness of 1.50 X 10-6 m. Hint: Use the appropriate formula to determine the friction factor, f to 4 decimal places (flow type dependant); g = 9.81 and round off to 3 decimal places for all other step calculations leading to the final answer including the final answer.