Q2-Consider a filamentary wire is bent to form a square loop of side 3 m lying in the x -y plane as shown in the figure. If the current flowing in the wire is I= 1Acalculate the magnetic flux density at the center of the loop will be 2 m 2 m

Q2-Consider a filamentary wire is bent to form a square loop of side 3 m lying in the x -y plane as shown in the figure. If the current flowing in the wire is I= 1Acalculate the magnetic flux density at the center of the loop will be 2 m 2 m

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter23: Electromagnetic Induction, Ac Circuits, And Electrical Technologies

Section: Chapter Questions

Problem 1PE: What is the value of the magnetic flux at coil 2 in Figure 23.56 due to coil 1? Figure 23.56 (a) The...

See similar textbooks

Similar questions

A time-dependent uniform magnetic field of magnitude B(t) is confined in a cylindrical region of radius R. A conducting rod of length 2D is placed in the region, as shown below. Show that the emf between the ends of the rod is given by dBdtDR2D2 . ( Hint: To find the between the ends, we need to integrate the electric field from one end to the other. To find the electric field, use Faraday’s law as “Ampere’s law for E”.)
Explain why the magnetic field would not be unique (that is, not have a single value) at a point in space where magnetic field lines might cross. (Consider the direction of the field at such a point.)
A square, flat loop of wire is pulled at constant velocity through a region of uniform magnetic field directed perpendicular to the plane of the loop as shown in Figure OQ31.5. Which of the following statements are correct? More than one statement may be correct. (a) Current is induced in the loop in the clockwise direction. (b) Current is induced in the loop in the counterclockwise direction. (c) No current is induced in the loop. (d) Charge separation occurs in the loop, with the top edge positive. (e) Charge separation occurs in the loop, with the top edge negative. Figure OQ31.5
A uniform magnetic field is directed along the x axis. For what orientation of a flat, rectangular coil is the flux through the rectangle a maximum? (a) It is a maximum in the xy plane. (b) It is a maximum in the xz plane. (c) It is a maximum in the yz plane. (d) The flux has the same nonzero value for all these orientations. (e) The flux is zero in all cases.
A nonconducting hard rubber circular disk of radius R is painted with a uniform surface charge density tr. It is rotated about its axis with angular speed . (a) Find the magnetic field produced at a point on the axis a distance h meters from the center of the disk, (b) Find the numerical value of magnitude of the magnetic field when =1C/m2 , R = 20 cm, h = 2 cm, and magnetic field of Earth, which is about 1/2 Gauss. =400rad/sec , and compare it with the magnitude of
A rectangular loop has dimensions 0.500 m by 0.300 m. The loop is hinged along the x-axis and lies in the xy-plane (Fig. P19.42). A uniform magnetic field of 1.50 T is directed at an angle of 40.0 with respect to the positive y-axis and lies parallel everywhere to the yz-plane. The loop carries a current of 0.900 A in the direction shown. (Ignore gravitation.) (a) In what direction is magnetic force exerted on wire segment ab? What is the direction of the magnetic torque associated with this force, as computed with respect to the x-axis? (b) What is the direction of the magnetic force exerted on segment cd? What is the direction of the magnetic torque associated with this force, again computed with respect to the x-axis? (c) Can the forces examined in parts (a) and (b) combine to cause the loop to rotate around the x-axis? Can they affect the motion of the loop in any way? Explain. (d) What is the direction (in the yz-plane) of the magnetic force exerted on segment bc? Measuring torques with respect to the x-axis, what is the direction of the torque exerted by the force on segment bc? (e) Looking toward the origin along the positive x-axis. Will the loop rotate clockwise or counterclockwise? (f) Compute the magnitude of the magnetic moment of the loop. (g) What is the angle between the magnetic moment vector and the magnetic field? (h) Compute the torque on the loop using the values found for the magnetic moment and magnetic field. Figure P19.42
(a) An MRI technician moves his hand from a region of very low magnetic field strength into an MRI scanner's 2.00 T field with his fingers pointing in the direction of the field. Find the average emf induced in his wedding ling, given its diameter is 2.20 cm and assuming it takes 0.250 s to move it into the field. (b) Discuss whether this current would significantly change the temperature of the ring.
A uniform magnetic field B=5.44104iT passes through a closed surface with a slanted top as shown in Figure P31.59. a. Given the dimensions and orientation of the closed surface shown, what is the magnetic flux through the slanted top of the surface? b. What is the net magnetic flux through the entire closed surface?
An N-turn circular wire coil of radius r lies in the xy-plane (the plane of the page), as in Figure P20.10. A uniform magnetic field is turned on, increasing steadily from 0 to B0 in the positive z-direction in t seconds. (a) Find a symbolic expression for the emf, , induced in the coil in terms of the variables given. (b) looking down on at the xy-plane from the positive z-axis, is the direction of the induced current clockwise or counterclockwise? (c) If each loop has resistance R, find an expression for the magnitude of the induced current, I.
A small, circular washer of radius a = 0.500 cm is held directly below a long, straight wire carrying a current of I = 10.0 A. The washer is located h = 0.500 m above the top of a table (Fig. P31.69). Assume the magnetic Held is nearly constant over the area of the washer and equal to the magnetic field at the center of the washer. (a) If the washer is dropped from rest, what is the magnitude of the average induced emf in the washer over the time interval between its release and the moment it hits the tabletop? (b) What is the direction of the induced current in the washer?
The magnetic field at all points within the cylindrical region whose cross-section is indicated in the accompanying figure starts at 1.0 T and decreases uniformly to zero in 20 s. What is the electric field (both magnitude and direction) as a function of r, the distance from the geometric center of the region?
A conducting sheet lies in a plane perpendicular to a magnetic field B that is below the sheet. If B oscillates at a high frequency and the conductor is made of a material of low resistivity, the region above the sheet is effectively shielded from B . Explain why. Will the conductor shield this region from static magnetic fields?