QI\ An ohmmeter has a moving coil of resistance 24 2 with 4mA full scale deflection current. The voltage of the battery is 4V. If a resistance of 20002 is used to give half scale deflection, calculate: The resistance R, and the shunt resistance. Q2\ Define an ohmmeter? What should be contained in it?

QI\ An ohmmeter has a moving coil of resistance 24 2 with 4mA full scale deflection current. The voltage of the battery is 4V. If a resistance of 20002 is used to give half scale deflection, calculate: The resistance R, and the shunt resistance. Q2\ Define an ohmmeter? What should be contained in it?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is CEMF?
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
A. Explain the difference between charging current andfaradaic current. B. What is the purpose of waiting 1s after a voltage pulse before measuring current in sampled current voltammetry? C. Why is square wave voltammetry more sensitive than sampled current voltammetry?
Cyclic Voltammetry and Charge-discharge The given figure is the Galvanostatic Charge-discharge curves of a supercapacitor made with MnO2 coated on a CNT electrode. Potential is measured with respect to time by applying different current densities. Based on the plot, answer the following questions 4. Is it possible to estimate maximum power of the device with this charge-discharge curve? If possible, explain how you would do it. (calculation is not necessary)
A- Calculate the equivalent resistances (???) of the following circuits. (The resistance value of the diodes in the conduction will be taken as 0, the resistance values of the diodes in the insulation will be taken as infinity. R1=10 ohms) B- Explain P and N type items by drawing figures. Explain the element formed by the non-polar combination of these substances by drawing a figure.
Subject: Circuits 1 What voltage will be required to produce a flow of 15A, through a resistance of 12 ohms?
A silicon semiconductor has a shape of a rectangular bar with a cross sectional area of 1x10-6cm2 and a lenght of 0.1 cm. How do i calculate the current through the semiconductor if a basis of 5 volts is applied across its length?
Consider the battery charging circuit shown in Figure 9.25 on page 476. The ac source has a peak value of 24 V and a frequency of 60 Hz. The resistance is 2 Ω, the diode is ideal, and VB = 12 V. Determine the average current (i.e., the value of the charge that passes through the battery in 1 second). Suppose that the battery starts from a totally discharged state and has a capacity of 100 ampere hours. How long does it take to fully charge the battery?
4. A single phase half-wave rectifier is connected to a 300V RMS 50Hz AC supply. If the rectifier is used to supply a resistive load of 500 Ohms. Calculate the equivalent DC voltage developed across the load, the load current and power dissipated by the load
Q6. How potential energy of water is converted into Electrical Energy? Q7. Draw the V-I Characteristic of Solar PV Cell ?
4 One of the methods of charging materials wherein the transfer of charges is due to the contact between two materials and depends also on the nature of the materials. Select one: a. charging by friction b. charging by conduction c. charging by induction d. charging by grounding