Q2: Equipment ratings for the four power system shown in Figure (1) are as follow: - GI 500 MVA, 13.8 kV, X = 0.2 p.u G2-750 MVA, 18 kV, X-0.18 p.u G3-1000 MVA, 20 kV, X-0.17 p.u TI = 500 MVA, 13.8/500 kV, XT1 0.12 p.u T2 750 MVA, 18/500 kV, XT2= 0.1 p.u T3-1000 MVA, 20/500 kV, XT3-0.1 p.u. (1) T1 T3 T.L1 G1 j50 ohm 13,8/500 KV 20/500 kV T.L 2 j50 ohm T.L 3 j50 ohm T2 G3 18/500 KV G2 Figure (1) neglecting resistance, transformer phase shift, and magnetizing reactance, draw the positive - sequence reactance diagram on a 1000 MVA, 20kV base in the G3.

Q2: Equipment ratings for the four power system shown in Figure (1) are as follow: - GI 500 MVA, 13.8 kV, X = 0.2 p.u G2-750 MVA, 18 kV, X-0.18 p.u G3-1000 MVA, 20 kV, X-0.17 p.u TI = 500 MVA, 13.8/500 kV, XT1 0.12 p.u T2 750 MVA, 18/500 kV, XT2= 0.1 p.u T3-1000 MVA, 20/500 kV, XT3-0.1 p.u. (1) T1 T3 T.L1 G1 j50 ohm 13,8/500 KV 20/500 kV T.L 2 j50 ohm T.L 3 j50 ohm T2 G3 18/500 KV G2 Figure (1) neglecting resistance, transformer phase shift, and magnetizing reactance, draw the positive - sequence reactance diagram on a 1000 MVA, 20kV base in the G3.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For loop ACDBA, what is the total voltage with 30 V for V1 , 90 V for V5 , 120 V for V3 and including 240 V applied voltage?
for the circuit shown, find the maximum power delivered to this load resistor? Please answer in typing format solution please only typing
Discuss the concept of load shedding and its purpose in a power system.
1- The recommended limit of voltage drop on a lighting circuit for a single-phase supply as per IEE Wiring regulations is equal to 6.3 volt. Then the value of supply voltage is a. 290V b. 250V c. 210V d. 230V 2- Which of the following statement is TRUE ? a. Resistance is not proportional to length of the material and Resistance is proportional to area b. Resistance is proportional to length of the material and Resistance is proportional to area c. Resistance is not proportional to length of the material and Resistance is inversly proportional to area d. Resistance is proportional to length of the material and Resistance is inversly proportional to area
A 12-kW, 240-volt range contributes _____ watts to the load when calculating the service by the standard method
1.a. To create usable voltages for 120-volt loads, _______ are usually installed.A. photovoltaic arraysB. transformersC. wind power turbinesD. generators1.b. Which grounding method is typically required of higher-voltage systems?A. Grounding through a high-impedance deviceB. Grounding through a low amount of resistanceC. Grounding through inductorsD. Grounding through surge arresters
a) IB =? , VCE= ? B) KV=V2/V1=? C)DEFINE THE DUTIES OF RB1 AND RB2 RESISTORS. ANSWER ALL QUESTIONS MORE!!!!
Q5. An essential part of the design of power supply network is the calculation of the currents which flow in the components when faults of various types occur. Explain briefly why fault calculation is an essential part of the design of power systems. Discuss the TWO different types of faults that are common in power systems; their causes; and method of calculation.
The figure attached to this question shows the 1 line diagram of a simple three bus power system with generation at bus 1. Please explain each step in your solution process. Will upvote!
In the distribution transformer;In the transformer used for the distribution of electricity to the houses, 3.3 kilovolts enters and 400 volts come out. When we make the phase-neutral calculation, that is, when we divide it by √3, we get 230 volts and 220 volts coming to the sockets. Where does the remaining 10 volts go? (Can you explain with figure) is this about 30 degree phase shift?
Equipment ratings for the four-bus power system shown in Figure 2 are as follows: Generator 1: 500 MVA, 13.8 kV, X" = 0.20 pu Generator 2: 750 MVA, 18 kV. X" = 0.18 pu Generator 3: 1000 MVA, 20 kV. X" = 0.17 pu Transformer Tl: 500 MVA, 13.8/500 kV, X = 0.12 pU Transformer T2: 750 MVA, 18/500 kV. X = 0.10 pu Transformer T3: 1000 MVA. 20/500 kV. X = 0.10 pU A three-phase short circuit occurs at bus 1, where the prefault voltage is 525 kV. Prefault current is neglected. Use 1000 MVA, 20 kV base in the zone of generator 3. By Thevenin's and Superposition approach, determine the following: a) subtransient fault current in amperes b) contributions to the fault current from the generators in amperes c) voltage at bus 2 during fault in kV
The course is power transmission system and the topic is Underground cables. Question : pressure cable are of two types. (i) oil filled cables. (ii) gas pressure cables What is the difference between two? Which one is good? Kindly explain the difference in detail