Q2 - Pseudo-Random Number Generator a) The following circuit is a pseudo-random number generator which uses linear feedback shift registers to produce a stream of outputs. The XOR tap at index 1' is responsible for generating this sequence of outputs. Fill in the table for the outputs of the 4 registers after each clock cycle. The initial output state is already provided in the first row. You can stop when the output starts to repeat and just say that it is repeating. QO Q1 Q2 Q3 Q D ClockEdge # Q3 Q2 Q1 QO 1 1 4 6. 7 10 11 12 13 14

Q2 - Pseudo-Random Number Generator a) The following circuit is a pseudo-random number generator which uses linear feedback shift registers to produce a stream of outputs. The XOR tap at index 1' is responsible for generating this sequence of outputs. Fill in the table for the outputs of the 4 registers after each clock cycle. The initial output state is already provided in the first row. You can stop when the output starts to repeat and just say that it is repeating. QO Q1 Q2 Q3 Q D ClockEdge # Q3 Q2 Q1 QO 1 1 4 6. 7 10 11 12 13 14

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question P( all part work u ) -Bit Shifting--- Recall that shift left is denoted by `<<`, and shift right is denoted by `>>`. Additionally, there is a logical and an arithmetic form of shift right. For this section, all your answers should consist of exactly 8 result bits. 31.) What is 01011110 << 1? 32.) What is 10101011 << 2? 33.) What is 10011011 >> 1, for _logical_ shift right? 34.) What is 01010011 >> 1, for _arithmetic_ shift right? Full explain this question and text typing work only We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line .
A 4-bit universal shifting register QA, QB, QC and QD and a single serial input called SI, has two inputs so that they determine how to operate, as follows: M0M1 = 00 indicates that it should keep the value of the current outputs, M0M1 = 01 indicates that you should shift right, M0M1 = 10 indicates that you should shift left, and M0M1 = 11 indicates that you should parallel load inputs A, B, C, and D. Design a minimum circuit that implement this record and draw the final schematic diagram. Include the entire design procedure
1-1-0-0 information is applied sequentially to the 4-bit shift register circuit, which consists of D FFs whose initial states are reset. What happens to the parallel information output at the fourth shift shift pulse?
Please design a sequence recognizer. I need state diagram of a Moore machine, the state transition table and the circuit diagram. When the 3 previous inputs to the circuit are “110” and the current output is “1,” then the output Z is equal to 1.
Please answer in detail. The outputs of four registers, A, B, C, D, H, L are connected through 8:1 line multiplexer to the input of a fifth register, X. Each register is 16 bits long. The required transfers are dictated by four timing variables, T0 through T3 as follows: T0 : X←A T1 : X←B T2 : X←C T3 : X←D The timing variables are mutually exclusive, which means that only one variable is equal to 1 at any given time, while the others are equal to 0. Draw a block diagram showing the hardware implementation of the register transfers. Include the connections necessary from the four timing variables to the selection inputs of the multiplexers and to the load input of register X. Note - Each register is 16 bits long and there are 8:1 multiplexers.
design a shift register which performs 1. Parallel load function, when input 00 will be applied in S1S0 respectively. 2. Shift up function , when input 01 will be applied in S1S0 respectively. 3. Shift down function , when input 10 will be applied in S1S0 respectively. 4. No change function , when input 11 will be applied in S1S0 respectively
Q1. Design a Shift register which performs:i) Parallel load function, when input 00 will be applied in S1S0 respectively. ii) Shift up function, when input 01 will be applied in S1S0respectively. iii) Shift down function, when input 10 will be applied in S1S0 respectively. iv) No change function, when input 11 will be applied in S1S0 respectively. Please solve this question
Please answer this question in 10 mins i will surely rate your answer. 1. A combinational circuit adds either a 1 or 2 to a 4-bit binary number A. Assume that the inputs bb A3, A2, A1, A0 represent the 4-bit binary number. Another input is a control signal C. The circuit has outputs assumed to be X3, X2, X1 and Xo, which represent the 4-bit number X. When C=0, X=A+1 and when C=1, X=A+2. Assume that the inputs for which X > (1111)2 will never occur. Show the design steps in detail including truth tables, K-Maps, logic equation minimisation. Finally, design this circuit using only NAND gates and inverters .
Q4. Starting from an initial value of R in Hex is B2 determine the sequence of binary values in R after a logical shift-left, followed by a circular shift-right, followed by a logical shift-right and a circular shift-left. explain through the proper diagrams
No plagiarism Do a research about shift registers and explain how the PISO shift register functions find real life applications.
Question:If you have two functions F(a,b,c) and G(a,b,c) to implement, what mux size and how many muxes would you need to implement F & G?My Comments:Is it as simple as using two 4-1 multiplexers because it will handle the 6 inputs? Or am I not understanding the function of a multiplexer?
2) Design a 2-to-1 multiplexer in which the inputs and outputs consist of single bits. Provide the truth table for this multiplexer using IN0 and IN1 for the two inputs, S for the select line and OUT for the output correctly. Obtain the minimal standard sum-of-products expression for the output correctly. PS: Please answer Number 3 from or after number 2 3) Obtain the schematic diagram for the mux designed in 2). Use proper conventions as to the labelling of part numbers, instance numbers and pin numbers correctly.