Q2/ The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant force R at A. 2 kN 0.5 m 1.5 m 70 To.15 m 0.15 m A 500 N-m L--x 1.2 kN

Q2/ The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant force R at A. 2 kN 0.5 m 1.5 m 70 To.15 m 0.15 m A 500 N-m L--x 1.2 kN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.63P: The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly...

See similar textbooks

Similar questions

The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
THE TWO MAIN CABLES OF THE AKASHI KAIYO SUSPENSIONBRIDGE IN JAPAN HAVE A SPAN L= 1990m AND A SAG H = 233m.THE LOADING ON EACH CABLE ISWO = 444.7 KN/m (withouttraffic) ALONG THE HORIZONTAL. DETERMINE THE CORRESPONDING MAXIMUM FORCE IN ONE OF THE CABLES. Give: Given, FBD, AND solution
Determine the forces in the bars caused by vertical load P that is applied at A
Determine the magnitude of the vertical force C, for the simply supported beam, where w = 11 kips/ft, L1 = 9 ft and L2 = 5 ft.
The truss has concentrated loads as shown. The wind loads of 25KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG by the method of joints.
Given: F1=5 kN F2=12 kN F3=4 kN F4= 11 kN L=8 m Determine the force in member CF by the method of sections.
The uniform 10 kg rod AB is supported by a ball and socket joint at A and by the cord CG that is attached to the midpoint G of the rod. Knowing that the rod leans against a frictionless vertical wall at B and that the tension in the cord CG, TCG=52.1 N, determine the following a.) Which of the following best shows the equivalent force-couple set at point A of the tension at cord CG, TCG? Choices: a F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 11.03 Nm j b F= -36.8 N i + 24.5 N j - 27.6 N k M = -7.36 Nm i - 29.4 Nm k c F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 11.03 Nm j d F= 36.8 N i - 24.5 N j + 27.6 N k M = 7.36 Nm i + 29.4 Nm k b.) Which of the following moments is equal to zero? Choices: The moment of the tension in cord CG, TCG about point OThe moment of the tension in cord CG, TCG about point AThe moment of the tension in cord CG, TCG about point BThe moment of the tension in cord CG, TCG about axis AB
Consider one end of a timber roof truss that is supported on a masonry wall. The reaction at the masonry wall must be only vertical. Assuming that the maximum capacity of either the inclined or horizontal members is 10 kips, determine the maximum magnitudes F1 and F2 so that their resultant is vertical through the masonry wall.
The truss above has concentrated loads as shown. The wind loads of 25 KN are perpendicular to the member AF. The forces acting on all members by the method of sections
A 5-m long simply supported timber beam carries two concentrated loads as shown. If L = 16 KN and M = 54 kN, determine the magnitude of the vertical force acting at support D.
2)All external force of 140N is applied to the truss at joint B. Draw the Free BodyDiagram of the truss.
The beam AB was designed to carry the uniformly varying load as shown. Determine the magnitude of the total load and the reaction at the supports